Zz 1=0 ^1 Zu 4 z = 0 ==l Figure shows a transmission line system. The effective dielectric constant of the transmission line is 4 and its length is 3 m. The source is a DC voltage source. The other parameters are as follows: with Vg = VG Volts, Zg = 20 Ohms, Zo = 40 Ohms, Z₁ = 60 Ohms. The switch is closed at t=0. a) Calculate and plot the voltage at the center of the transmission line as a function of time between 0 ns and 80 ns. b) Calculate and plot the current at the center of the transmission line as a function of time between 0 ns and 80 ns.

Zz 1=0 ^1 Zu 4 z = 0 ==l Figure shows a transmission line system. The effective dielectric constant of the transmission line is 4 and its length is 3 m. The source is a DC voltage source. The other parameters are as follows: with Vg = VG Volts, Zg = 20 Ohms, Zo = 40 Ohms, Z₁ = 60 Ohms. The switch is closed at t=0. a) Calculate and plot the voltage at the center of the transmission line as a function of time between 0 ns and 80 ns. b) Calculate and plot the current at the center of the transmission line as a function of time between 0 ns and 80 ns.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Two impedances are connected in parallel across a 220-volt source. If Z1= 4 cis (30) and Z2 = 5 cis (60) ohms. Find the equivalent admittance ( Siemen ) of the circuit. O 0.435 cis(- 43.3) O 2.3 cis (43.3) O 0.835 cis (-53.3) O 0.835cis (53.3)
When a resistor is connected across the terminals of an ac generator (117 V) that has a fixed frequency, there is a current of 0.332 A in the resistor. When an inductor is connected across the terminals of the same generator, there is a current of 0.365 A in the inductor. When both the resistor and the inductor are connected in series between the terminals of this generator, what is (a) the impedance of the series combination and (b) the phase angle between the current and the voltage of the generator? Note: The ac current and voltage are rms values and power is an average value unless indicated otherwise. (a) Number (b) Number Buda i Vrms R Irms.R Circuit 1 Units Units Vrms. Irms, L Circuit 2 > L Vrms R www Circuit 3
an ac circuit has a frequency of 400 hz. a 16- ohms resistor, a 0.0119-h inductor, and a 16.6- uf capacitor are connected in series. If the voltage connected to the circuit is 440v. How many degrees are the voltage and current out of phase with each other?
Impedance of AC circuit and Admittance of AC circuitSHOW THE CIRCUIT USING ANY SOFTWARE OR YOU CAN DRAW IT MANUAALYY thNAKSS
7- DC Chopper with output voltage of 120V and input voltage of 80V and output power of 240W. Assume lossless chopper. The average inductance current IL is * 2.6 A 3.0A 4.3A
Due to mutual inductance between two coils, there is an induced emf in one coil due to a change in current in the other coil. O True O False O Hard to say
9. What is sinp from impedance triangle? a) Xµ/R b) Xµ/Z C) R/Z d) Z/R
X 23) WhatsApp Meet hpd-sdbt-qho yl la- Chrome a web.whatsapp.com YouTube Gmal M Course Jalllbi th Select one: O True O False the machine is generating 355 V at 60 H The e.m.f generated by a synchronous generator at a frequency of 40H2 and field current of 2.7A is field current of 3A. ENG 4 ProBook 4340 SISP POWAN
Practically in the field, the transmission line connected between the generating station and transmission substation is represented with its Reactance Resistance Admittance Impedance
phase The conductirs in a singke line are 6m above the guünd. gnünd. Each conductrs are spaced 3m a pant. Calculate the capacitance Capaci tance per milo, of the live if' bothe thu conductors radii s 75 mum. a.erdudlirg ground ef fet (ufvestal) b. mcluding gound effed.
root locus z plane
Determine o such that the peak value of i(t) is I,=1A W=......rad/s i i (t) 100 0.002F Vs(t)=25cos(@t)