i need the answer quickly 19. Which A/D converter is considered to be simplest, fastest and mostexpensive?a) Servo converterb) Counter type ADCc) Flash type ADCd) All of the mentioned20. The flash type A/D converters are called asa) Parallel non-inverting A/D converterb) Parallel counter A/D converterc) Parallel inverting A/D converterd) Parallel comparator A/D converter21. What is the advantage of using flash type A/D converter?*a) High speed conversionb) Low speed conversionc) Nominal speed conversiond) None of the mentioned22.Drawback of counter type A/D convertera) Counter clears automaticallyb) More complexc) High conversion timed) Low speed23.Calculate the conversion time of a 12-bit counter type ADC with 1MHZclock frequent to convert a full scale input?a) 4.095 usb)4.095msc) 4.095sd) None of the mentioned24.A 12 bit dual ramp generation has a maximum output voltage of +12v.'Compute the equivalent digital number for the analog signal of +6v.a) 1000000000b) 10000000000c) 1000000000000d) 100000000000

Note :- As per guidelines,we are supposed to answer only 3 questions. So I request you to please…

19. Which A/D converter is considered to be simplest, fastest and most expensive? a) Servo converter b) Counter type ADC c) Flash type ADC d) All of the mentioned 20. The flash type A/D converters are called as a) Parallel non-inverting A/D converter b) Parallel counter A/D converter c) Parallel inverting A/D converter d) Parallel comparator A/D converter 21. What is the advantage of using flash type A/D converter? a) High speed conversion b) Low speed conversion c) Nominal speed conversion d) None of the mentioned

19. Which A/D converter is considered to be simplest, fastest and most expensive? a) Servo converter b) Counter type ADC c) Flash type ADC d) All of the mentioned 20. The flash type A/D converters are called as a) Parallel non-inverting A/D converter b) Parallel counter A/D converter c) Parallel inverting A/D converter d) Parallel comparator A/D converter 21. What is the advantage of using flash type A/D converter? a) High speed conversion b) Low speed conversion c) Nominal speed conversion d) None of the mentioned

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In continuous conduction mode, the switching frequency in a DC/DC converter influences which following properties: A. Input voltage B. Inductor ripple magnitude C. Component size D. Efficiency of the converter
The inversion mode is possible in single phase half controlled converter with RL load. Select one: O True O False
11 The shown circuit represents Q1 Vs C Load buck converter boost converter full-bridge DC-DC converter half-bridge DC-DC converter
Single phase full wave controlled converter circuit is powered by a single phase source. When the trigger angle is 0 °, the DC output voltage taken from the output of the converter circuit is 300V. If the trigger angle is 60 °, what is the value of the DC output voltage to be obtained at the output? i have 1 houre
please work out the following using the infomation in the attached photo. This is for a Boost converter (a) Output voltage(b) Inductor current ripple (assume it is 20%) (c) Switching frequency (d) Output current (e) Output voltage ripple
For Steady-State Operation o f Boost DC-DC Converter What is the duty ratio (D) How can it effects on the converter output (Vo)
the way of work buck dc-to-dc converter
Design a buck converter such that the output voltage is 28V when the input is 48V. The load is 8Ohm. Design the converter such that it will be in continuous current mode. The output voltage ripple must not be more than 0.5%. Specify the frequency and the values of each component. Suggest the power switch also
hich of the following statements about DC-DC converters is false? A) The maximum value that the continuous operating limit of the coil current can take in the booster type converter is d=1/3. B) none C) In case the switch is on (off) in the step-down converter, the input voltage is not used by any of the circuit elements. D) buck-boost type converters It is obtained by connecting buck and boost type converters in succession. E) In the step-up converter, when the switch is ON, the input source only feeds the coil. Question Which of the following statements about DC-DC converters is false? A) The maximum value that the continuous operating limit of the coil current can take in the booster type converter is d=1/3. B) none C) In case the switch is on (off) in the step-down converter, the input voltage is not used by any of the circuit elements. D) buck-boost type converters It is obtained by connecting buck and boost type converters in succession. E) In the step-up…
The DC-DC converter below is fed from a 96 V DC source and it is desired to obtain 24 V output voltage on 15 2 load resistors. The switching frequency of the converter is 50 kHz. It is desired that the fluctuation rate in the output voltage should not exceed 1%. VL + mr Etc + Vx a) What is the minimum required coil inductance? b) What is the minimum required capacitor value? drink IR
In the figure shown below, the duty ratio of the buck converter is a and the duty ratio of the boost converter is B. The input voltage of the buck converter is 15 V and the output voltage of the boost converter is 45 V. the correct relationship between a and B? + 15 V a Buck B Boost 45 V
The DC-DC converter below is fed from a 96 V DC source and it is desired to obtain 24 V output voltage on 15 2 load resistors. The switching frequency of the converter is 50 kHz. It is desired that the fluctuation rate in the output voltage should not exceed 1%. VI VL mo ic İR a) What is the minimum required coil inductance? b) What is the minimum required capacitor value?