in2. Find the economic dispatch for a total demand of 450 MWsystem with three thermal units described below. Fromprevious solution of ELD, the optimum dispatch for Demand=500"P₂=72.816' P₁ = 197.498 Assume thisMWgivenas P₁=229.686 M"answer as base point and use participation factors to find answerdemand. Compare the results with problem 3 in homework 2.for new2Unit DataH₁ = 225 +8.4P, +0.0025P²H₂ = 729 + 6.3P₂ + 0.0081 P²H3 = 400 + 7.5P3 +0.0025P3MWMinimum Maximum(MW) (MW)454547.5350350450Fuel Cost(R/MBtu)0.801.020.90

Given: Total demand PD=450 MW,Previous solution of Economic load dispatch ELD=500 MW,P1=229.686…

2. Find the economic dispatch for a total demand of 450MW system with three thermal units described below. From MW MW " . previous solution of ELD, the optimum dispatch for Demand=500" given as P₁ = 229.686 P₂ = 72.816 MM, P₁ = 197.498 MW Assume this answer as base point and use participation factors to find answer for new demand. Compare the results with problem 3 in homework 2. in a MW

2. Find the economic dispatch for a total demand of 450MW system with three thermal units described below. From MW MW " . previous solution of ELD, the optimum dispatch for Demand=500" given as P₁ = 229.686 P₂ = 72.816 MM, P₁ = 197.498 MW Assume this answer as base point and use participation factors to find answer for new demand. Compare the results with problem 3 in homework 2. in a MW

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.31P: Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in...

See similar textbooks

Similar questions

a. What is the unit load per ft2 for the general lighting load of a residence? ____ b. What are the demand factors for the general lighting load in dwellings? ____
What effects are produced by change in voltage? 1. Iron los..........varies approximately as V². 2. Cu loss..........it also varies as V² but decreases with an increase in voltage if constant kVA output is assumed. 3. Efficiency...........for distribution transformers, efficiency at fractional loads decreases with in- crease in voltage while at full load or overload it increases with increase in voltage and vice- versa. 4. Regulation..........it varies as but decreases with increase in voltage if constant kVA output is assumed. 5. Heating.........for constant kVA output, iron temperatures increase whereas Cu temperatures decrease with increase in voltages and vice-versa.
7. TY Hat CHICL Ans. 1. Iron los.........varies approximately as V². 2. Cu loss..........it also varies as ² but decreases with an increase in voltage if constant kVA output is assumed. 3. Efficiency...........for distribution transformers, efficiency at fractional loads decreases with in- crease in voltage while at full load or overload it increases with increase in voltage and vice- versa. 4. Regulation..........it varies as but decreases with increase in voltage if constant kVA output is assumed. 5. Heating.........for constant kVA output, iron temperatures increase whereas Cu temperatures decrease with increase in voltages and vice-versa. quems
A generator operating at 50 Hz delivers 1 p.u. power to an infinite bus through a transmission circuit in which resistance is ignored. A fault takes place reducing the maximum power transferable to 0.5 p.u. Where as before the fault, this power was 2.5 p.u. and after the clearance of the fault, it is 2 p.u. The value of 8 is max
A 500 MVA synchronous machine has H, = 5.6 MJ/MVA and a 1200 MVA machine has H₂ = 2.0 MJ/MVA. The two machines operate in parallel in a power station. What is the equivalent. H constant for the two, relative to a 100 MVA base?
Which of the following statements is/are true? A In purely resistive circuit, the current lags voltage. (B In purely capacitive circuit, the voltage lags current. In purely resistive circuit, the current is in phase with voltage. D In purely inductive circuit, the current leads voltage.
Table Q2a Time (hours) 0-6 6-12 12-14 14-18 18-24 Load (MW) 45 90 135 150 75 Referring to the Table Q2a; i) Draw the load curve and the load duration curve [Use the graph paper provided] ii) Indicate the base load and the peak load on the graph. Determine the values for both loads. iii) Choose the suitable generating units to supply the load and list their operating schedules. Later, compute the total installed capacity. iv) Calculate the load factor and the plant capacity factor. Discuss the impact on the operating schedule if the plant capacity factor increases to 0.9.
State Kirchhoff’s Current Law.
Which of the following statements is/are true? (A In purely inductive circuit, the current leads voltage. (B) In purely resistive circuit, the current lags voltage. C In purely resistive circuit, the current is in phase with voltage. D In purely capacitive circuit, the voltage lags current.
2. a) Explain the terms load factor and diversity factor. b) Discuss the advantages of interconnected grid system. c) A generating station is to supply four regions of load whose peak loads are 10 MW, 5 MW, 8 MW and 7 MW. The diversity factor at the station is 1-5 and the average annual load factor is 60%. Calculate: (i) the maximum demand on the station, (ii) annual energy supplied by the station and (iii) suggest the installed capacity and the number of units.
Consider a 3-phase, 50 HZ, 11 KV distribution system. Each of conductors is suspended by an insulator string having two identical porcelain insulators. The self-capacitance of the insulator is 5 times the shunt capacitance between link and ground. Find the voltages across two insulators.
Q20. The section bus-bars A and B as shown in Figure B5 are linked by a bus-bar reactors each rated at 5000 kVA with 10% reactance. On bus-bar A, there are two generators each of 10,000 kVA with 10% reactance and on B two generators each of 8000 kVA with 12 % reactance. Find the Current and MVA that fed into a dead short circuit between all phases on B with bus-bar reactor in the circuit. Page 4 of 5 جامعة التقنية والعلومر التطبيقية بإبراء University of Technology and Applied Sciences - Ibra Student ID: Section: Student Name: 8,000 kVA 12% 10,000 kVA 10,000 kVA 10% 8,000 kVA 12% 10% 2 3 5,000 kVA 10% lell 8,000 kVA 10% Figure B5 "End of Question Paper"