2. The strings AB and AC connect the 200 g ball to the vertical shaft, as shown in Fig. 2. The shaft rotates at a constant angular speed w and the ball travels in a horizontal circle with the strings inclined at a = 300 to the shaft. Given that the tension in string AC is 4 N. B 200–g Fig. 2 (400 mm 400 mm

2. The strings AB and AC connect the 200 g ball to the vertical shaft, as shown in Fig. 2. The shaft rotates at a constant angular speed w and the ball travels in a horizontal circle with the strings inclined at a = 300 to the shaft. Given that the tension in string AC is 4 N. B 200–g Fig. 2 (400 mm 400 mm

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.60P: The force P applied to the brake handle enables the band brake to reduce the angular speed of a...

See similar textbooks

Similar questions

A tractor is now drafted in to move the blo ck. The weight of the tractor is equally distributed over all four wheels and it pulls on the blo ck via a rope with tension T. The back wheels have a diameter of 1.6m and the front wheelshave a diameter of 80cm. The tractor motor generates a torque of τ on each of its back wheels that have radii Rb and masses mb. The front wheels of the tractor are smaller than the back wheels and have radii Rf and masses mf. Both sets of wheels can b e treated as uniform solid disks with moment ofinertia I = 1/2mR2. The mass of the tractor body, without the wheels, is M. If the wheels don't slip, show that the tractor can accelerate the block with an acceleration of (see image)
The strings AB and AC connect 500-g mass A to the vertical shaft BC. When the shaft rotates with a constant angular velocity of 15 rad/s, the ball has circular motion in the horizontal plane with the strings having angles of a = 55° shown in the figure. Find the tension forces at the strings AB and AC. B 500g 400 mm 400 mm
A torque T = 0.30 N-m is applied to a bevel gear B. Bevel gear D meshes with gear B and drives pump A. Gear B has a radius of gyration of 150 mm and a weight of 50 N, whereas gear D and the im- peller of pump A have a combined radius of gy- ration of 50 mm and a weight of 100 N. Find how many revolutions of gear B are needed to get the pump up to 200 rpm from rest. What is the power output of the pump at this speed if it is 90% efficient.
The strings AB and AC connect 500-g mass A to the vertical shaft BC. When the shaft rotates with a constant angular velocity of 15 rad/s, the ball has circular motion in the horizontal plane with the strings having angles of ? = 55° shown in the figure. Find the tension forces at the strings AB and AC.
Form the figure shown, a flexible belt placed around a rotating drum of 4-inch radius acts as a brake when the arm ABCD is pulled down by the force P. The coefficient of kinetic friction between the belt and the drum is 0.7. What force P that ● would result in a braking torque of 400 lb • in., assuming that the drum is rotating counterclockwise. Neglect the weight of the brake arm. 60° 4 in.. A B |--2 in.-² 4 in. 1-2 60° 2 in. D Р
The 544g collar is free to slide on the smooth rod OA. The rod rotates about pin O at constant angular velocity, é. a =en + še, = a = RÔ?e, + RÖe, for a circular path, R = radius 2.1 Use N-T coordinates, draw a FBD and a kinetic diagram to determine the minimum value of é for which the collar will maintain contact with the stop at A throughout the rotation. 2.2 Would friction between the collar and the rod affect your result in 2.1?
a) In the Fig Q4(in the attatched image) shows a system of four unbalanced masses. Determine the bearing reactions if the rotor speed is 600 r.p.m.
The strings AB and AC connect 500-g mass A to the vertical shaft BC. When the shaft rotates with a constant angular velocity of 15 rad/s, the ball has circular motion in the horizontal plane with the strings having angles of a = 55° shown in the figure. Find the tension forces at the strings AB and AC. 500g A uui 00t 00 mm
Solve the reaction forces.
Equilibrium of Concurrent Force System. The piston of a reciprocating engine exerts a force of 175 kN on the crosshead when the crank is 45° (angle B) past TDC. If the stroke of the piston is 800 mm and the length of the connecting rod is 1.80 m, find the guide force and the force in the connecting rod. Hint: 1=½ stroke; Angle o may be solved using Sine Law in AACO. K= Compressive Force in the connecting Rod E= Piston Effort 70 120 F, = Guide Force Fig. P-1 Fig. P-2 a Tools: EF cos0=0; F sin .=0. R = Ev)* + (E#): ; R 771 =- : tane = sin A sin B sin C
Question 2: The ideal spring of constant k-2.6 kN/m is attached to the disk at point A and the end fitting at point B, as shown. The spring is unstretched when OA and Oв are both zero. If the disk is rotated 15° clockwise and the end fitting is rotated 30°counterclockwise, determine the vector expression for the spring force F. ( Determine distance C so that the moment the spring force makes about the Z axis is equal to 10.82 N.m. ( A = 15°. C A 250 mm eeeeeee 900 mm k= 2.6 kN/m OB = 30° B LC 7-y 200 mm
Q5 / Two cable are tied together at (c) and are loaded as shown in fig (5). Determine the tension in cable Ac and Bc ? Notice : use the law of sines to solve the question 5. Fig(5) B 75 75° 200 kg