a) Fig. 3 shows a gear train that is attached to a rack labelled A. The rack is capable of moving up and down. Determine linear velocity and direction of the rack if the input gear 2 rotates at 1200 rpm counterclockwise. Assume the raduis of gear 8 is 12cm and all the number of teeth of the gear given in the diagram. W₂ = 1200 rev/min 18T 3 15T 44T 5 33T 16T 36T 8 48T A

a) Fig. 3 shows a gear train that is attached to a rack labelled A. The rack is capable of moving up and down. Determine linear velocity and direction of the rack if the input gear 2 rotates at 1200 rpm counterclockwise. Assume the raduis of gear 8 is 12cm and all the number of teeth of the gear given in the diagram. W₂ = 1200 rev/min 18T 3 15T 44T 5 33T 16T 36T 8 48T A

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the simple gear train below, Gear A is the input gear and rotates at 2500 rpm and Gear D is the output gear for this simple gear train. The number of teeth for each gear is as follows: NA = 116 Teeth, NB = 178 Teeth, NC = 70 Teeth and ND = 120 Teeth Calculate the output angular velocity at Gear D (ωD). Give your answer in rads-1to the nearest radian.
For the simple gear train below, Gear A is the input gear and rotates at 2500 rpm and Gear D is the output gear for this simple gear train. The number of teeth for each gear is as follows: NA = 116 Teeth, NB = 178 Teeth, NC= 70 Teeth and ND= 120 Teeth Calculate the output angular velocity at Gear D (wD). Give your answer in rads-1 to the nearest radian. Gear B Gear A Gear D Input Gear A (2500 rpm) Output Gear D Answer:
Q4: In an epicyclic gear train shown in the figure, the number of teeth of gear (A and S) are (200 and 98) respectively. If the gear (S) rotate with speed (450 r.p.m.) in C.W. direction and the gear (A) rotate with speed (100 r.p.m.) in C.C.W. direction, Determine the speed of the gear (P) and the arm (H). [Note: Start motion from gear (S)]. A Good Luck
4. For the gear train in a watch shown in the following figure. The teeth number are z,=20, z,=40, Z3=18, z4-50, Z5=25, Z6-20, z,=54. Please calculate Speed ratio 17 1 VIIA 3 5 4 6 2 7
Q5 For the simple gear train below, Gear A is the input gear and rotates at 2500 rpm. The number of teeth for each gear is as follows: NA = 60 Teeth, Ng = 84 Teeth, Nc=36 Teeth and Np = 60 Teeth. - Calculate the output angular velocity at Gear D (wp).Give your answer in rads to the nearest radian. Gear D is the output gear for the simple gear train shown below. Gear B Gear A Gear D 84 60 60 Gear C 36 Input Gear A (2500 rpm) Output Gear D
A three-stage automobile transmission is shown schematically. The number 6 crankshaft has an angular angle of 50 rad / s.Find the angular velocity (w1) of the drive shaft no. 1 as it rotates with speed [w6 = 50 rad / s]. Each of the spur gears has a fixedrotates around the axis. It should be noted that gears 6 and 5, 4 and 3, 2 and 1 engage each other.. Division Circle of Gearsdiameters d6 = 180mm; d5 = 60mm; d4 = 60mm; d3 = 100mm; d2 = 140mm and d1 = 120mm.
For the simple gear train below, Gear A is the input gear and rotates at 2500 rpm. The number of teeth for each gear is as follows: NA = 60 Teeth, NB = 84 Teeth, Nc= 36 Teeth and Np = 60 Teeth. Calculate the output angular velocity at Gear D (wp).Give your answer in rads to the nearest radian. Gear D is the output gear for the simple gear train shown below. Gear B Gear A Gear D 84 60 Gear C 60 36 Input Gear A (2500 rpm) Output Gear D Answer:
For the simple gear train below, Gear A is the input gear and rotates at 2500 rpm and Gear D is the output gear for this simple gear train. The number of teeth for each gear is as follows: NA = 116 Teeth, NB = 178 Teeth, NC = 70 Teeth and ND = 120 Teeth Calculate the output angular velocity at Gear D (WD). Give your answer in rads-1 to the nearest radian. Gear B Gear A Gear D Gear C Output Gear D Input Gear A (2500 rpm) Answer:
For the simple gear train below, Gear A is the input gear and rotates at 2500 rpm. The number of teeth for each gear is as follows: NA = 60 Teeth, NB = 84 Teeth, NC = 36 Teeth and ND = 60 Teeth.Calculate the output angular velocity at Gear D (ωD).Give your answer in rads-1 to the nearest radian. Gear D is the output gear for the simple gear train shown below.
Q6/ An epicyclic gear train shown, the gears A and B are internal gears and the gear C-D is a compound gear. The gears E and F have the same pitch and number of teeth (T. Tr=18), Te = 28 and Ta 26. (1) Find the number of teeth on A and B: (2) If the arm G makes 100 rpm clockwise and A is fixed, find the speed of B and (3) If the arm G makes 100 rpm clockwise and wheel A makes 10 rpm counter clockWise find the speed of wheel B. (Note A and B not a compound gears) %3D
As shown in the figure a planetary gear train consist of the arm C coupled to two gears A and B with 40 and 60 teeth respectively. If the arm rotates at 150 rpm in the anticlockwise direction about the center of the fixed gear A. Calculate the speed of gear B. How fast will gear B move if the gear A makes 300 rpm in the clockwise direction instead of being fixed. (must use Tabular method) B Arm C C A B Nber of teeth Total rotations
) Gear A is the input and revolves at 1200 rev/min clockwise viewed from the left end. The input torque is 30 Nm and the efficiency is 70%.Gear A has 50 teeth Gear B has 150 teeth Gear C has 30 teeth Gear D has 60 teeth Output Input Figure Q3a Determine the following. The output speed and its direction. The total velocity ratio The output power. The holding torque for gear box i. ii. iii. iv.