A plate clutch consists of one pair of contacting surfaces. The inner and outer diameters of the friction disk are 100mm and 200mm respectively. The coefficient of friction is 0.2 and the permissible intensity of pressure is 1 N/mm?. Assuming uniform wear theory, calculate the torque transmitted by the clutch.

A plate clutch consists of one pair of contacting surfaces. The inner and outer diameters of the friction disk are 100mm and 200mm respectively. The coefficient of friction is 0.2 and the permissible intensity of pressure is 1 N/mm?. Assuming uniform wear theory, calculate the torque transmitted by the clutch.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A multiple friction clutch is required to transmit 89.52 kW at 3000 rpm. The plates are alternatively of steel and phosphor bronze and they run in oil. The coefficient of friction is 0.08. The internal radius of the friction surface is 0.8 times the radius of the external surface. The axial pressure is limited to 20 x 104 N/m2 . If the maximum diameter of the frictional surface is not to exceed 250 mm, determine the number of plates required.
A multiplate friction clutch is required to transmit 72 kW at 3600 r.p.m. The plates are alternately steel and phosphor bronze and they run in oil. The coefficient of friction is 0.071. The mean axial pressure is 0.14 N/mm? and the internal radius of the friction surfaces is 0.8 of the external radius, which is 125 mm. Find out the number of plates reauirod
What is the difference between kinetic and static friction. Given example of each.
Q2/ A dry single plate clutch is to be designed for an autontotive vehicle whase engine is ated to give 100 &W at 2400 r.p.M. and marimum torque 500 N-m. The outer radus of the friction plate is 25% ore than the inner radius, The intensity of pressure berween the plate is not to exceed 0.07 N/mm. The coefficient of friction may be assamed egual t0 0.3 The helical springs reguired by this cluich to provide axial force mecessary to engage the clutch are eight. If cach spring has stiffness equal to 40 N/mm, derermine the dimensions of the friction plate and initial compression in the springs
The axial pressure on a single disc clutch (both sides of the disc is effective) is limited to 0.12 Mpa. This is designed for a vehicle with 13kW power at a speed of 700 rpm. Assume uniform wear conditions and a friction coefficient of 0.25. If the outer dimater of the disc is 1.25 times the internal diameter, determine the dimensions of the disc lining and the axial force exerted by the springs.
A multiple disc clutch has three discs on the driving shaft and two on the driven shaft, providing four pairs of contact surfaces. The outer diameter of the contact surfaces is 250 mm and the inner diameter is 150 mm. Determine the maximum axial intensity of pressure between the discs for transmitting 18.75 kW at 500 r.p.m. Assume uniform wear and coefficient of friction as 0.3.
An automobile single plate ciutch consists of a pair of contacting surfaces. The inner and outer radii of friction plate are 120.mm and 250 mm respectively. Coefficient of friction is 0.25 and the total axial force is 20 kN. Calculate the power transmitting capacity of the clutch at 600 pm by using: (0) Uniform wear theory () Uniform pressure theory.
A multiplate disc clutch transmits 55 kilowatt of power at 1800 rpm. Coefficient of friction for the friction surface is 0.1. Axial intensity of pressure is not to exceed 160 KN/m2. The internal radius is 80mm and is 0.7 times external radius. Find the number of plates needed to transmit the required torque.
A block of concrete weighs 20 kg, it takes 40 N to start the block sliding on a concrete floor and 10 N to maintain sliding. Calculate the Static coefficiant of friction and calculate the kinetci coefficiant of friction My question is; what is the coefficiant of static and kinetic friction. Ive read throught the book and cant seem to find anything that explains it. I found a formula which reads F = Static coefficiant multiplied by the weight of the block. But that doesnt tell me exactly what the coeffciant of each is, Is it a constant? or does it vary based on the item being moved? Thank you.
BELT FRICTION. PLEASE include the Beta or angle of contact between 2 belt and pulley to solve to problem Thankyou Please regard to the solution because my instructor said that the answer there has been already checked many times and that was the outcome maybe your solution will comeup closer to the answer as much as possible. Please include the friction for all the surface contact not only in the surface but also in the contact between Belt and The Pulley which is 0.25. Thankyou!
Q: A single plate clutch, effective on both sides, is required to transmit 20 kW at 2500 rpm. Determine the outer and inner diameters of frictional surface if the coefficient of friction is 0.26 and check their with wear rating. The maximum pressure is not to exceed 0.002 N/mm?. Also, determine the axial thrust to be provided by springs. Clutch plate with friction lining ‘Body Bl X Pressure plate Hub Thrust Springs Flywheel Crank shaft Bl Driven shaft riving shaft 4 Release lever (withdrawl finger) O Knife edge
Q1/ 4 plate clutch having a single driving plate with contact surfaces on each side is required to transmit 110 kW at 1250 r.p.m. The outer diameter of the contact surfaces is to be 300 mm. The coefficient of friction is 0.4. (a) Assuming a uniform pressure of 0.17 N/mm? ; determine the inner diameter of the friction surfaces. (b) Assuming the same dimensions and the same total axial thrust, determine the maximum torque that can be transmitted and the maximum intensity of pressure when uniform wear conditions have been reach.