b) An automotive clutch driven plate is clamped between a fly- wheel and a sprung pressure plate. The outer diameter of the friction lining is 300mm, the inner, 250mm, and the coefficient of friction between the friction lining and the cast iron of the fly- wheel and pressure plate is 0.3. The maximum torque of the en- gine is 310Nm and the maximum power of the engine is 210AW. Using a factor of safety of 1.2, calculate the minimum clamping force to prevent slipping.

b) An automotive clutch driven plate is clamped between a fly- wheel and a sprung pressure plate. The outer diameter of the friction lining is 300mm, the inner, 250mm, and the coefficient of friction between the friction lining and the cast iron of the fly- wheel and pressure plate is 0.3. The maximum torque of the en- gine is 310Nm and the maximum power of the engine is 210AW. Using a factor of safety of 1.2, calculate the minimum clamping force to prevent slipping.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1/ A plate clutch having a single driving plate with contact surfaces on each side is required to transmit 110 kW at 1250 r.p.m. The outer diameter of the contact surfaces is to be 300 mm. The coefficient of friction is 0.4. (a) Assuming a uniform pressure of 0.17 N/mm? ; determine the inner diameter of the friction surfaces. (b) Assuming the same dimensions and the same total axial thrust, determine the maximum torque that can be transmitted and the maximum intensity of pressure when uniform wear conditions have been reach.
An multi axial plate clutch used in injection molding machine consist of a three pairs of contact surfaces for engaging and disengaging power from the engine. The engine used for power has a maximum torque capacity of 120 N-m and is transmitted to machine without losses. The permissible intensity of pressure is 350 kPa and the coefficient of friction is 0.35 for the clutch system used in the machine. It was determined that the machine will operate on maximum capacity of torque if the ratio of inner diameter to outside diameter of the axial clutch is 0.577. Assuming uniform wear theory, calculate the inner and outer diameters of the friction lining.
A multi-plate clutch must transmit 11 kW of power without slipping at 1500 rev/min. The coefficient of friction is 0.3. The inner and outer radis are 30 and 85 mm respectively. The axial force applied to the plates is 780 N. Determine the number of plates required using.
A car engine has its rated output of 120 kW. The maxdmum torque developed is 110 Nm, The clutch used is of single plate type having two active surfaces. Axia! pressure is not to exceed 0.85 bar. External diamater of friction plate is 1.25 times the internal diameter. Determine the dimensions of friction plate and axial force exerted by the spring. Assume uniform wear and coefficient of friction to be 0.3.
The axial pressure on a single disc clutch (both sides of the disc is effective) is limited to 0.12 Mpa. This is designed for a vehicle with 13kW power at a speed of 700 rpm. Assume uniform wear conditions and a friction coefficient of 0.25. If the outer dimater of the disc is 1.25 times the internal diameter, determine the dimensions of the disc lining and the axial force exerted by the springs.
Q2/ A dry single plate clutch is to be designed for an autontotive vehicle whase engine is ated to give 100 &W at 2400 r.p.M. and marimum torque 500 N-m. The outer radus of the friction plate is 25% ore than the inner radius, The intensity of pressure berween the plate is not to exceed 0.07 N/mm. The coefficient of friction may be assamed egual t0 0.3 The helical springs reguired by this cluich to provide axial force mecessary to engage the clutch are eight. If cach spring has stiffness equal to 40 N/mm, derermine the dimensions of the friction plate and initial compression in the springs
Q2/ A dry single plate clutch is to be designed for an automotive vehicle whose engine is rated to give 100 kW at 2400 r.p.m. and maximum torque 500 N-m. The outer radius of the friction plate is 25% more than the inner radius. The intensity of pressure between the plate is not to exceed 0.07 N/mm?. The coefficient of friction may be assumed equal to 0.3. The helical springs required by this clutch to provide axial force necessary to engage the clutch are eight. If each spring has stiffness equal to 40 N/mm, determine the dimensions of the friction plate and initial compression in the springs
Determine the axial force required to engage a cone clutch transmitting 25 kW power at 750 rpm. Average friction diameter of the cone is 400 mm, semicone angle 10°and coefficient of friction 0.25.
Q3 /A multi - plate clutch is to transmit 12 kW at 1500 r.p.m. The inner and outer radii for the plates are to be 50 mm and 100 mm respectively. The maximum axial spring forces is restricted to 1 kN. Answer the following questions 1- The necessary number of pairs of surfaces is u= 0.35 assuming constant wear. 2- The necessary number of pairs of surfaces is constant pressure. u= 0.18 assuming 3- The axial force 4- Percentage increase in forces is
A A multiple disc clutch transmits 55 kW of power at 1800 r.p.m. The coefficient of friction is 0.1 and the axial intensity of pressure is not to exceed 160 kN/m. The internal radius is 80 mm and is 0.7 times the external radius. Find the number of plates needed to transmit the required torque.
(b) A single plate clutch has a driven plate with an annular friction lining of 380 mm outside diameter and 270 mm inside diameter. The pressure between the flywheel face and the pressure plate is 159 kN/m² and the coefficient of friction is limited to 0.28. Determine: The torque that can be transmitted by the clutch, The power transmitted at a speed of 350 rpm.
A multiplate disc clutch transmits 55 kilowatt of power at 1800 rpm. Coefficient of friction for the friction surface is 0.1. Axial intensity of pressure is not to exceed 160 KN/m2. The internal radius is 80mm and is 0.7 times external radius. Find the number of plates needed to transmit the required torque.