A synchronous logic circuit has one JK flip-flop, one D flip-flop, and one input. There is no output at the circuit. The input is represented with the letter X. Y, is the output of D flip-flop, Yo is the output of JK flip-flop respectively. The logic functions for the flip-flop's inputs are given below. J = XY, K = X+ Y,, D = X(Y, + Y1) %3D %3D Draw the state diagram of the synchronous logic circuit. Note: (Y,Yo)2 shall represent the state.

A synchronous logic circuit has one JK flip-flop, one D flip-flop, and one input. There is no output at the circuit. The input is represented with the letter X. Y, is the output of D flip-flop, Yo is the output of JK flip-flop respectively. The logic functions for the flip-flop's inputs are given below. J = XY, K = X+ Y,, D = X(Y, + Y1) %3D %3D Draw the state diagram of the synchronous logic circuit. Note: (Y,Yo)2 shall represent the state.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

A synchronous logic circuit has one JK and one D flip-flop. There is no output in the circuit. The entry is represented by an X. Y is the output of JK flip-flob, and Yo is the output of D flip-flobe. Logic functions of the inputs of flip-flops are given below. J = XY. K = X, D = XY, A Draw the state diagram of the synchronous circuit. Note: Take the states (Y, Yo) in 2 order.
Design a combinational logic circuit with four inputs A, B, C, D and one output F as follows. The inputs ABCD represent a four-bit unsigned binary number where A is the most significant bit and D is the least significant bit. Whenever the inputs represent an even number between 0 and 10, the output F is logic 1. Otherwise F is logic 0. Show all your working.
4 7) For the following sequential circuit: a) Tabulate the state table. b) Derive the state and output equations. c) Re-design the circuit using T flip-flops. Q1 Q -y K, K QP Jo Qo Q Ko K Q clock. please solve it as soon as possible
Design the following combinational logic circuit with a four-bit input and a three-bit output. The input represents two unsigned 2-bit numbers: A1 A0 and B1 B0. The output C2 C1.C0 is the result of the integer binary division A1 A0/B1 B0 rounded down to three bits. The 3-bit output has a 2-bit unsigned whole part C2 C1 and a fraction part CO. The weight of the fraction bit CO is 21. Note the quotient should be rounded down, i.e. the division 01/11 should give the outputs 00.0 (1/3 rounded down to 0) not 00.1 (1/3 rounded up to 0.5). A result of infinity should be represented as 11.1. A minimal logic implementation is not required. (Hint: start by producing a truth table of your design).
A clock generator has been connected to J-K flip flop which had an input frequency of 512 kHz. The system is required to generate two frequencies, 128 kHz and 16 kHz at the outputs. Design a circuit that will generate the required output frequencies.
The storage elements (memory) used in clocked sequential circuits are called A flip-flop is a binary storage device capable of storing one bit of information. In a -- the output of a flip-flop is either O or 1. Fill in the blanks
2. Sequential circuit shown below has two flip-flops A and B and one input x. It consists of a combinatorial logic connected to the flip-flops, as shown in Figure below. Analyze the circuit: a. Derive the next state and output equations. b. The state table of the circuit. c. Draw the state diagram. A K. 2-t0-1 MUX Y B' CLK
Analyze the following sequential circuit: 1) What type of state machine is this circuit and why? 2) Write equations for flip-flop inputs and output (Y). 3) Derive the next-state equation for each flip-flop from its input equations. 4) Derive the State table. X A' B' LA DA D. A B
Use the following state diagram and create the state table for a synchronous to detect the sequence. The circuit has a single input, x, and a single output z. The output is logic-1 whenever the input sequence 1001 is detected, logic-0 otherwise. Note that overlapping sequences are allowed, Create the initial state table, and the complete state table. Write the equations for all the state variables and the output z. 1 so S1 S2 S3 Z=0 Z=1 State diagram of 1001 sequence recognizer
Use the following state diagram and create the state table for a synchronous to detect the sequence. The circuit has a single input, x, and a single output z. The output is logic-1 whenever the input sequence 1001 is detected, logic-0 otherwise. Note that overlapping sequences are allowed, Create the initial state table, and the complete state table. Write the equations for all the state variables and the output z. 1 SO s1 S2 S3 Z=0 Z=1
No Change (NC) condition appears in a J-K flip-flop when O a. J= 0, K = 0 O b. J= 0, K = 1 O c. J = 1, K = 1 O d. J= 1, K = 0
Rp 5. Complete the waveforms for the circuit of Figure 2. Cp Rp # Sp. K 0 D 6. Complete the waveform for Q for the flip-flop of Figure 3. Cp 0 0 14 0 310 3 Figure 2 Figure 3 D - Cp 1 Sp 7474 30-13 RD 9 RD J Q 5645 e Sp Sp Rp Rp Q Q