Air discharges from a 2-in.-diameter nozzle and strikes a curved vane, which is in a vertical plane, as shown below. A stagnation tube connected to a water U-tube manometer is located in the free air jet. Determine the horizontal component of the force that the air jet exerts on the vane. Neglect the weight of the air and all friction. Air Open Water Stagnation Fixed vane tube 7 in. [2-in. dia. Free air jet X30 30°

Air discharges from a 2-in.-diameter nozzle and strikes a curved vane, which is in a vertical plane, as shown below. A stagnation tube connected to a water U-tube manometer is located in the free air jet. Determine the horizontal component of the force that the air jet exerts on the vane. Neglect the weight of the air and all friction. Air Open Water Stagnation Fixed vane tube 7 in. [2-in. dia. Free air jet X30 30°

Name: Problem 5.2.28 of Gehart, et al. (Problem 66, 7th ed.)Air discharges
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Problem 5.2.28 of Gehart, et al. (Problem 66, 7th ed.)Air discharges from a 2-in.-diameter nozzle and strikes a curved vane, which is in a vertical plane, as shownbelow. A stagnation tube connected to a water U-tube manometer is located in the free

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water in a vertical (i.e., gravitational force of the fluid in the nozzle plays a role, and the elevation change in the Bernoulli's Equation, if needed, should be considered) pipe is charging from an attached bend nozzle into the atmosphere as shown in Fig. 5. The nozzle's weight is 20 kg. The pipe and the nozzle are connected by a flange. The gage pressure of the flow at the flange is 35 kPa when the discharge rate is 0.1 m³/s. The volume of the bending nozzle is 0.012 m³. Calculate the vertical component of the anchoring forcing required to hold the nozzle in place and determine its direction. G= 9.81 m/s². The density of water is 1000 kg/m³. ChatGPT solution: Nozzle 1 Area -0.01 m² P-35 kPa Area -0.025 m² 0.10 ms Figure 5: Q5 35 degree
The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10.3 m of water, and the water level in the sump is 3 m below the pump cylinder axis.3.1 Find the maximum allowable speed to operate the pump3.2 What power is expected in overcoming friction at this speed, take ƒ = 0.01
The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10.3 m of water, and the water level in the sump is 3 m below the pump cylinder axis. 3.1 Find the maximum allowable speed to operate the pump 3.2 What power is expected in overcoming friction at this speed, takef = 0.01
In an experiment a jet of water of diameter 20 mm is fired vertically upwards at a sprung target thatdeflects the water at an angle of 120° to the horizontal in all directions. If a 500g mass placed on thetarget balances the force of the jet, what is the discharge of the jet in litre/s?
A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open manometer reads a vacuum of 20 cm of mercury. The pipe is 10 cm in diameter and the flow is 35 L/s of water. Find the total energy at the location of the manometer, relative to a datum, through the pump. ( WITH FREE BODY DIAGRAM ) CHOIECES: A.2.56 B.-2.72 m C.12.74 m D.-4.67 m
A very popular toy on the market several years ago was the water rocket. Water (at 10°C) was loaded into a plastic rocket and pressurized with a hand pump. The rocket was released and would travel a considerable distance in the air. Assume that a water rocket has a mass of 50g and is charged with 100g of water. The pressure inside the rocket is 100kPa gage. The exit area is one-tenth of the chamber cross-sectional area. The inside diameter of the rocket is 5cm. Assume that Bernoulli’s equation is valid for the water flow inside the rocket. Neglecting air friction calculate the maximum velocity it will attain.
1. A Jet of water 50 mm diameter is discharging under a constant head of 70 meters. Find the force exerted by the jet on a fixed plate. Take coefficient of velocity as 0.9.
1. A water jetpack suspends a 7Okg man in air without motion along the vertical and the horizontal as the man tilts the platform. The jetpack has two outlets, each has a diameter of 5cm, and an inlet with a diameter of 6cm. Calculate the volumetric flowrate, in and out of the water jetpack, and the angle 00 such that there is no motion along any direction. Neglect the weight of the jetpack. The inlet is perpendicular to the outlet. inlet W W Qi 2Q. ВАCK SIDE
(Linear momentum) A nozzle is attached to an 77.1-mm inside-diameter flexible hose. The nozzle area is 482 mm2. If the delivery pressure of water at the nozzle inlet is 652 kPa. (a) determine the anchoring force must be exerted by the hands holding the hose and nozzle stationary. i Ib (b) Could you hold the hose and nozzle stationary?
2. Oil (sg=0.90) is flowing at 150 L/min through a turbine. The pressure before the turbine is 750 kPa and after the turbine 150 kPa with an elevation between these two points of 2.3 m [ fluid entrance is on the high side ]. If the friction loss in the system is 5.10 N.m/N find (a) the power delivered to the turbine by the fluid and (b) If the mechanical efficiency of the turbine is 80 % find the power output from the turbine.
An industrial tank is discharging a fluid through a 5-inches nozzle with a velocity of 5 meters per second. At the same time, receiving a fluid at a rate of 225 US Gal per minute. At a certain post the tank is considered to be quarter full. Find the (a) water level and the (b) mass change In the tank 15 minutes later. Given: tank diameter = 10 ft tank height = 20 ft
The open stream of water seen in the following picture emerges from a nozzle into the atmosphere at sea level, where it then collides with a stagnation tube. If we exclude losses and assume that the pressure at the centerline of section 1 is 110 kPa, we can estimate that the (a) the mass flow measured in kilograms per second (kg/s), and (b) the height, measured in meters, of the fluid in the stagnation tube.