ProductActuator / ValvePackagingFigure Q2 Q2As an engineer working in ABABA Sdn. Bhd., you are required to design apackaging process based on Figure Q2 for an orange cold drink.a) To maintain the temperature of the beverage, you are required to choosebetween thermistor, thermocouple and RTD. State the difference between thethree and the reason for choosing the sensor.

Answered: Image /qna-images/answer/55f43c9f-04b5-45e6-b46e-4d6a55b1c833.jpg

Answered: Actuator / Valve Packaging Figure Q2

Engineering

Electrical Engineering

Actuator / Valve Packaging Figure Q2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Comparing the performance with controlled rectifier circuit which one of the following statement is correct for DC -DC chopper ? O a. Regenerative braking process is very slow O b. Efficiency is poor in chopper circuit O c. small filters are required O d. Switching frequency is not responsible for output ripples
About sources, check the correct statement(s). a) A power supply is composed of at least six parts, they are: AC power, transformer, rectifier, filtering capacitor, voltage regulator and load.b) The transformer must be a voltage step-down.c) We have the options of half wave rectifier circuit, full wave rectifier circuit and bridge full wave rectifier circuitd) Regardless of the rectifier circuit used, we need to insert a filtering capacitore) The filtering capacitor must be placed in series with the loadf) We usually use an electrolytic capacitor as a filtering capacitor in power supplies.g) These are characteristics of the filtering capacitor: it opposes variations in electrical voltage, the ability to store charges depends on its capacitance.h) The filter capacitor needs a current limiting resistor connected in seriesi) Among the techniques used as a voltage regulator we have: The zener diode, LM317, LM78XX and LM 79XX.j) If we are going to build a symmetric source, we will have to…
B / Answer the word true or false and the 1 The electrodynamic device is used to measure the frequency phase angle. 2 The basis of the electrodynamic device depends on the torque proportional to the current. 3 The rectifier type Inst. To measure voltage and direct that is current.
Comparing the performance with controlled rectifier circuit which one of the following statement is wrong for DC -DC chopper ? a. small filters are required O b. Regenerative braking process is very slow O c. Switching frequency is responsible for output ripples O d. Efficiency is better in chopper circuit
A single phase fully controlled rectifier has RL load. Write the following a) Draw its circuit diagram and waveform. b) Draw and explain its quadrant operation. c) Explain why the negative voltage appear across the load. d) Explain how the negative voltage can be removed. L
Comparing the performance with controlled rectifier circuit which one of the following statement is correct for DC -DC chopper ? a. Switching frequency is not responsible for output ripples b. small filters are required c. Regenerative braking process is very slow d. Efficiency is poor in chopper circuit
1- Calculate the theoretical output DC voltage of the full wave center tap rectifier circuit and compare it with measured value. For the capacitive filter, obtain the theoretical values of the DC output voltage and the ripple voltage and compare these values with the measured quantities. 2- What is the necessity of the transformer in the rectifier circuit? 3- Can a rectifier made in INDIA (V=230v, f=50HZ) be used in USA (V=110v, f=60HZ)? 4- Discuss your results stating the error sources.
1.What is the main difference between Center tapped Full wave Rectifier and Bridge Rectifier? 2.How could you reduce the Ripple factor? 3.Explain the positive clipping operation with circuit diagram and Waveforms.
By comparing the performance of DC -DC chopper with controlled rectifier circuit which one of the following statement is wrong ? O a. Efficiency is better in chopper circuit b. small filters are required in chopper circuit O c. Regenerative braking process is very slow in chopper circuit O d. Switching frequency is responsible for output ripples in chopper circuit Clear my choice
A Three Phase Uncontrolled Bridge Rectifier is operated from a three phase starconnected 210V, 60Hz ac supply through a star/star connected transformer.(i) Draw the circuit configuration.(ii) Draw the waveform of three phase secondary voltages showing conductiontimings of each individual diode, duration of each conduction sequence and outputvoltage during each sequence.(iii) Draw the output voltage waveform.(iv) Calculate the average output voltage.
Interpret the circuit by answering the guide questions, this is a simple power supply with full-wave bridge type rectifier. Define the following: ac source, fuse, SPST switch, transformer, full- wave rectifier, capacitor as a filter, load (resistive load). b. How does this power supply circuit work? а. FULL-WAVE BRIDE RECTIFIER TRANSFORMER ON/OFF SWITCH FUSE FILTER DC OUTPUT VOLTAGE AC LOAD SOURCE
The figures represent respectively: choose 1 alternative A)The output voltage waveform of a “full wave bridged” type rectifier and the output voltage waveform of a “full wave with center tap transformer” type rectifier only. B)The output voltage waveform of a “full wave bridged” rectifier and the output voltage waveform of a “half wave” type rectifier only. C)The waveform of the output voltage of a “half wave” rectifier and the waveform of the output voltage of a rectifier which can be either the “full wave bridged” or “full wave” type (with center tap). D)None of the above answers are correct.