At a machined shaft shoulder the small diameter d is 1.100 in, the large diameter D is r 1.65 in, and the fillet radius is 0.11 in. The bending moment is 1260 lbf in and the steady torsion moment is 1100 lbf in. *Hint: Refer to Table A-15's to obtain the stress concentration factors, K, and Kts a) What is the maximum bending stress in the shaft?

At a machined shaft shoulder the small diameter d is 1.100 in, the large diameter D is r 1.65 in, and the fillet radius is 0.11 in. The bending moment is 1260 lbf in and the steady torsion moment is 1100 lbf in. *Hint: Refer to Table A-15's to obtain the stress concentration factors, K, and Kts a) What is the maximum bending stress in the shaft?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figure on the right shows a shaft (Ç1040, Sut=500MPa) housed with “A” and “B” bearings. Said shaft is driven by an electric motor. The torque of the spindle is transferred to a wheat mill (not shown!) with the help of the “C” belt pulley mechanism. According to this; a) Max. Calculate the bending stress and location? b) Calculate the maximum torsional stress and location in the shaft? c) Calculate the safety factor of the shaft against static damage according to the Tresca and von Mises criteria?
A steel shaft can be manufactured as a circular rod with a solid body or a circular tube. The shaft is required to bear a torsion moment of 1200 N.m. The shear safety stress for the shaft material is 40 MPa, the largest permitted unit torsion angle in the bar is 0.75º/m. The shear modulus of steel is G=78 GPa. a) Find the required diameter d0 for a solid circle shaft. b) Find the required outer diameter d2 for a ring-section shaft with a thickness in tenths of the outer diameter. c) Find the diameter ratio (d2/d0 ratio) and the weight ratio for ring cross section and solid section shafts.
3. A circular solid shaft, with an radius of 20 mm and a length of 5 m and thin bearings at both ends, is subject to a point loading 1000 N in the middle. The young's modulus (E) is 200 GPa. Draw a shear force diagram (SFD) and a bending moment diagram (BMD) of this shaft. i. Compute the maximum deflection in the middle of the shaft. a) Hint: You should compute I (the second moment of inertia of the cross- section of the shaft) prior to determining the deflection. b) Hint: Use the table shown in the lecture note for calculating the ii. deflection. iii. cross section of the shaft. Compute the maximum shear stress due to a vertical shear force at a Hint: Use the formula to compute the shear stress. The maximum shear stress occurs at the neutral axis of the cross section of a shaft. Compute the maximum normal stress due to a bending moment at a iv. cross section of the shaft. Hint: Use the formula to compute the normal stress. The maximum normal stress occurs at the top or bottom of the…
A shaft is subjected to a torque of 28 kNm and a maximum bending moment of 25 kNm. The shaft is solid with a diameter of 125 mm. Using the Mohr circle method find the values for the principal stresses and themaximum shear stresses on the shaft i)Construct the Mohr circle on the graph paper provided. ii) Using the Mohr circle method find the values for the principal stresses and the maximum shear stresses on the shaft.iii) Show the orientations of the planes on which the principal stresses act on a rotatedelement
A steel shaft can be manufactured as a circular rod with a solid body or a circular tube. The shaft is required to bear a torque of 1200 N.m. Since the shear strength for the shaft material is 40 MPa, the maximum permitted unit torsion angle of the bar is 0.750 / m and the shear modulus of the steel is G = 78 GPa;a) Find the required diameter d0 for a solid circle shaft.b) Find the required outer diameter d2 for a ring section shaft whose thickness is 1/10 of the outer diameter.c) Find the diameter ratio (d2 / d0) and the weight ratio for ring cross section and solid section shafts.
2-Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. (i) power tranmission = 230 kW(ii) speed = 80 rpm,(iii) Maximum shear stress = 60 MPa(iv) diameter ratio = 1.74(v) The maximum value of the twisting moment is 40% greater than its mean. (i) The mean torque is (Unit is in Nm)=__________ (ii) The maximum torque is (Unit is in Nm)=__________ (iii) The outer diameter of the shaft (unit in mm)=_______________ (iv) The inner diameter of the shaft (unit in mm)=_______________
A steel shaft ABCD of length L = 6.5 is shown in Figure 4. Given the torque at A, B, C andD is 80 kNm, 150 kNm, 60 kNm and 10 kNm, respectively. The shaft has a diameter of200 mm.a) Determine the angle of twist of the end A. b) Calculate the angle of twist of A relative to C. c) Plot a diagram of torque, T versus length, L of the shaft.
Perform double integration of the bending moment equations. You will obtain deflections in this form (can be found in the image attached) Calculate: the value of the constant integration C2. Enter your answer in kNm2 to three decimal places. b) the value of the integration constant C4. Enter your answer in kNm2 to three decimal places. c) the value of the deflection at point C. Enter your answer in mm to three decimal places.
a) The factors of safety predicted at point H by the maximum shear stress theory of failure (Tresca criterion) i) The second moment of area relative to z-axis, I_z, for the cross-section can be calculated as ( Enter your answer in cm4 ii) The bending stress at Point H can be calculated as (Enter your answer in MPa, Compressive stress is negative and tensile stress is positive) iii) The first moment of area required to calculate shear stress at H can be calculated as (Enter your answer in mm^3) iv) The absolute value of the transverse shear stress at point H can be calculated as (Enter your answer in MPa ) v) Maximum principal stress can be calculated as (Enter your answer in MPa ) vi) Minimum principal stress can be calculated as (Enter your answer in MPa ) vii) The equivalent stress for Maximum-Shear-Stress Theory ( Tresca criterion) (Enter your answer in MPa ) b) The von Mises equivalent stresses at point H can be calculated as: MPa c) The factors of safety at point H…
PLEASE ANSWER ASAP TY! The shaft shown has a diameter of 30 mm and is fixed at points A and B. Shear Modulus = 75 GPa. a) What is the internal torque in segment AC (in N-m)? b) Determine the maximum torsional shear stress experienced at segment AC (in MPa). c) What is the torsional shear stress at the center of the cross-section of the shaft (in MPa)? d) Determine the reactive torque at point B (in N-m).
A steel shaft in the form of a solid body circular rod or a circular tubecan be manufactured. The shaft is required to bear 1200 N.m of torsional torque. Anti-shear stress for shaft material 40 MPa, largest permissible unit torsion angle in the rod 0.75 ^ 0As / m and steel's shear modulus is G = 78 GPa;a) Find the required diameter d0 for a solid circular shaft.b) Find the required outer diameter d2 for a ring-section shaft whose thickness is one tenth of the outer diameter.c) Find the diameter ratio (d2 / d0 ratio) and the weight ratio for ring cross section and solid section shafts. please solve carefully and in detail thank you
5) Find the maximum shear stress in each shaft for the following arrangement. Assume the diameter value of all shafts is same (50 mm) and material is steel (G-85 GPa) Dimensions in mm 40 500 Nm