Consider a round potato being baked in an oven.Would you model the heat transfer to the potato as one-, two-, or three-dimensional by writing of the differential equations? (Steady state and no heat generation)Would you model the heat transfer for steady or transient system consisting of heat generation by writing of the differential equations?If the system is transient and consisting no heat generation, write initial boundary condition for one-dimensional the differential equation for the potato? QUESTIONConsider a round potato being baked in an oven.1) Would you model the heat transfer to the potato as one-, two-, orthree-dimensional by writing of the differential equations? (Steadystate and no heat generation)2) Would you model the heat transfer for steady or transient system consisting of heatgeneration by writing of the differential equations?3) If the system is transient and consisting no heat generation, write initial boundarycondition for one-dimensional the differential equation for the potato?

Fourier's law is the foundation of conduction heat transfer. Fourier's law defines thermal…

Consider a round potato being baked in an oven. Would you model the heat transfer to the potato as one-, two-, or three-dimensional by writing of the differential equations? (Steady state and no heat generation) Would you model the heat transfer for steady or transient system consisting of heat generation by writing of the differential equations? If the system is transient and consisting no heat generation, write initial boundary condition for one-dimensional the differential equation for the potato?

Consider a round potato being baked in an oven. Would you model the heat transfer to the potato as one-, two-, or three-dimensional by writing of the differential equations? (Steady state and no heat generation) Would you model the heat transfer for steady or transient system consisting of heat generation by writing of the differential equations? If the system is transient and consisting no heat generation, write initial boundary condition for one-dimensional the differential equation for the potato?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter4: Numerical Analysis Of Heat Conduction

Section: Chapter Questions

Problem 4.21P

See similar textbooks

Similar questions

Let's assume that the outdoor temperature in your region was 1 C on 26.12.2002. Let's assume that you use a 2088 W heater in the room in order to keep the indoor temperature of the room at 20 ° C. In the meantime, a 68 W light bulb for lighting, a computer you use to solve this question and load it into the system (let's assume it consumes 217 W of energy), you and your two friends (three people in total) are in the room to assist you in solving the questions. A person radiates 45 J of heat per second to his environment. When you consider all these conditions, calculate the exergy destruction caused by the heat loss from the exterior wall of your room.
One-dimensional, steady-state conduction with uniform internal energy generation occurs in a plane wall which is subject to convection on the left side at x = 0 and being well-insulated on the other.a) Specify the mathematical model defining T(x): provide a governing differential equation and appropriate boundary conditions. Express your answer in terms of defined variables rather than numerical values with units. b) Solve for the temperature profile T(x) referencing the x-origin as shown on the left surface (again expressing your answer in terms of defined variables rather than numericalvalues.) c) Find the maximum temperature in the wall and the wall surface temperature if the volumetric generation is qdot = 1 MW/m^3 with the remaining parameters as specified in the figure.
You have a 1-D steady-state conduction problem, constant thermal properties, with energy generation q_dot. The material is 4.0 cm thick and has a constant thermal conductivity of k = 65.0 (W/m-k). The temperature distribution within the object is: T(x) = a + bx^2 a = 100 Celcius b = -1000 Celcius/m^2 Starting with the Heat Diffusion Equation and using the data given above, determine the following: • Determine the heat generation rate q_dot within the wall. • Determine the heat flux q" at x=0 and at x=L.
I am able to find the first row and the first column of by hand. However, When I do the 2nd row and 2nd column, my answer doesnt match my matlab code. Would someone be able to help me? Thank you! Use the explicit method to solve by hand the 1D heat equation for the temperature distribution in a laterally insulated wire with a length of 1 cm, whose ends are kept at T(0) = 0 0C and T(1) = 0 0C, for 0 ≤ x ≤ 1 and 0 ≤ t ≤ 0.5. At t = 0, the temperature of the wire is subjected to initial condition T(x) = 100sin(πx). Use the following values of k = 0.15 cm2/s, Δx = 0.25 cm, and Δt = 0.1 s. Calculate by hand the values of temperature at the internal mesh points only for the first time row at t = 0.1 s. Verify the values of temperature at t = 0.1 s calculated by hand. Use Heat1DCN.m M-file to solve the 1D heat equation within the space-time domain 0 ≤ x ≤ 1 and 0 ≤ t ≤ 2 with Δx = 0.05 cm and Δt = 0.1 s. Make the plot of temperature surface.
Q3: Consider evaluation of different temperatures of solar photovoltaic/thermal system (PVT) as shown in Figure 1(a). The following set of differential equations represent energy balance equations to be solve using matrices and eigenvalues using MATLAB: dTglass = -0.75Tgtass + 0.75TpvT (1) dt - 1.187glass – 22Tpyr + 23Twax (2) dt dTwax 12Tglass + 18TpyT – 19 Twax (3) dt Where, Tgtass , TPVT, and Twax, are temperatures illustrated in Figure 1(b). At time t-0 the initial conditions are Tglass = 35 , Tpyr = 33, and Twax = 31 °C. Cold suppty In frem water Tank Glass PVT Espann Nane-PCMPVT Collector Wax Tubes Sterg Tank Nanofluid Heat Exchanger Contalner Tepe Teek oe Pump for drain
Drive an expression for heat transfer and temperature distribution for steady state one dimensional heat conduction in a plan wall. The temperature is maintained at a temperature Ti at x=0, while the other face X-L is maintained at temperature T2, the thickness of the wall may be taken as L and the energy equation is given by: d²T/dx² = 0. : Sketch a simple diagram for the temperature distribution in plane wall for a steady state one dimensional heat conduction, with heat generation. The surface temperature of the walls Ti and T2, for the cases Ti>T2, T1-T2, and T2>T1. The thickness of the wall may be taken as 2L
The amount of heat conducted through a wall of length r is given by Fourier's Law:. CONDUCTION RATE EQUATION T FOURIER'S LAW q, = -k A dT dx T, >T, where q, is the heat flux, k is a proportionality factor, Ais the wall's cross-sectional area, and 4 is the temperature gradient throughout the wall. Our friend Matt Labb wants to find T2 (temperature of the wall's rightmost edge) given q,, k, and A. Is this possible? If so, briefly explain how to find Tp. If not, briefly explain why.
. You are involved in an industry to find solution of the following situation: In the process to disinfect water by using chlorine gas, it is important to produce the gas within the company plant location. The process that is used to produce chlorine gas involves the electrolysis of NaCl to produce chlorine gas at the anode and hydrogen gas at the cathode, then the chlorine gas is used to disinfect the water while the hydrogen gas is vented to the atmosphere. The rate of hydrogen production is 10 m3/day, the calorific value of H2 is 130000 kJ/kg, ρ=0.09 g/L. You are involved in investigating two alternatives:I. Hydrogen is collected, introduced to hydrogen engine to produce work. Then this work is used to produce electricity.II. Hydrogen is stored and used directly to produce electricity by hydrogen fuel cell (a) Calculate the efficiency of the first alternative (conversion of heat to work) for energy absorption at the combustion temperature of 500 oC and energy rejection to the cold…
lail - Ahmed Amro Hussein Ali A x n Course: EN7919-Thermodynamic x Homework Problerns(First Law)_S x noodle/pluginfile.php/168549/mod_resource/content/1/Homework%20Problems%28First%20Law%29_SOLUTIONS.pdf UTIONS.pdf 4 / 4 100% Problem-4: When a system is taken from a state-a to a state-b, the figure along path a-c-b, 84 kJ of heat flow into the system, and the system does 32 kJ of work. (i) How much will the heat that flows into the system along the path a-d-b be, if the work done is 10.5 kJ? (Answer: 62.5 kJ) (ii) When the system is returned from b to a along the curved path, the work done on the system is 21 kJ. Does the system absorb or liberate heat, and how much? (Answer:-73 k]) (iii) If Ua = 0 andU, = 42kJ , find the heat absorbed in the processes ad and db. (Answer: 52.5 kJ, 10 kJ)
A velocity of a vehicle is required to be controlled and maintained constant even if there are disturbances because of wind, or road surface variations. The forces that are applied on the vehicle are the engine force (u), damping/resistive force (b*v) that opposing the motion, and inertial force (m*a). A simplified model is shown in the free body diagram below. From the free body diagram, the ordinary differential equation of the vehicle is: m * dv(t)/ dt + bv(t) = u (t) Where: v (m/s) is the velocity of the vehicle, b [Ns/m] is the damping coefficient, m [kg] is the vehicle mass, u [N] is the engine force. Question: Assume that the vehicle initially starts from zero velocity and zero acceleration. Then, (Note that the velocity (v) is the output and the force (w) is the input to the system): 1. What is the order of this system?
A velocity of a vehicle is required to be controlled and maintained constant even if there are disturbances because of wind, or road surface variations. The forces that are applied on the vehicle are the engine force (u), damping/resistive force (b*v) that opposing the motion, and inertial force (m*a). A simplified model is shown in the free body diagram below. From the free body diagram, the ordinary differential equation of the vehicle is: m * dv(t)/ dt + bv(t) = u (t) Where: v (m/s) is the velocity of the vehicle, b [Ns/m] is the damping coefficient, m [kg] is the vehicle mass, u [N] is the engine force. Question: Assume that the vehicle initially starts from zero velocity and zero acceleration. Then, (Note that the velocity (v) is the output and the force (w) is the input to the system): A. Use Laplace transform of the differential equation to determine the transfer function of the system.
The wall (thickness L) of a furnace is comprised of brick material (thermal conductivity, k = 0.2 Wm¯' K'). Given that the atmospheric temperature is 0°C at both sides of wall, the density (p) and heat capacity (c) of the brick material are 1.6 gm cm³ and 5.0 J kg K¯l respectively. du Solve pc = k- subject to initial conditions as u(x,0) = x²(L – x). ốt Consider the case 2=- p² only.