Consider a step down converter supplied by a DC power source of magnitude Vs = 100 V. The switching period is 0.2 ms. The load is resistive with R-5 Ohms. An LC filter is used to regulate the output with L= 5 mH and C-200 uF. The switch is ideal. The average output voltage is Va= 50V. The ripple current of the inductor delta (1) and the ripple voltage of filter capacitor delta (V) are respectively equal to: Select one: O a. 1A, 0.125V O b. 0.9A, 0.1V O c. 0.96A, 0.12V O d. None of these

Consider a step down converter supplied by a DC power source of magnitude Vs = 100 V. The switching period is 0.2 ms. The load is resistive with R-5 Ohms. An LC filter is used to regulate the output with L= 5 mH and C-200 uF. The switch is ideal. The average output voltage is Va= 50V. The ripple current of the inductor delta (1) and the ripple voltage of filter capacitor delta (V) are respectively equal to: Select one: O a. 1A, 0.125V O b. 0.9A, 0.1V O c. 0.96A, 0.12V O d. None of these

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Boost Converter Design A boost converter is required to have an output voltage of 8 V and supply a load current of 1 A. The input voltage varies from 2.7 to 4.2 V. A control circuit adjusts the duty ratio to keep the output voltage constant. Select the switching frequency. Determine a value for the inductor such that the variation in inductor current is no more than 40 percent of the average inductor current for all operating conditions. Determine a value of an ideal capacitor such that the output voltage ripple is no more than 2 percent. Determine the maximum capacitor equivalent series resistance for a 2 percent ripple.
100 used to compand A companding system with u from 0V to 10 V sinusoid signal. Draw the characteristic of the typical system.
Design a Cuk converter that has an input of 25V and the output of -30V. The load is 60W. Specify the duty ratio, switching frequency, inductor values and capacitor values. The maximum change in inductor currents must be 20 percent of the average currents. The ripple voltage across capacitor C1 must be less than 5 percent, and the output ripple voltage must be less than 1 percent.
C'uk Converter Design A C'uk converter has an input of 12 V and is to have an output of - 24 V supplying a 60 W load. Select the duty ratio, the switching frequency, the inductor sizes such that the change in inductor currents is no more than 12 percent of the average inductor current, the output ripple voltage is no more than 1.5 percent, and the ripple voltage across C1 is no more than 3 percent.
az/a.Design Circint as the following pescripton: A. the positive Cyycle of the vout signal is 3-2 and Negadive cycle is 4-3 (Note: we must used preetical Diodes and vin is tov)
2. Determine the input and output impedances given the figure below. The op-amp datasheet gives Zin 3.5 MQ, Zout = 82 Q, and Aol = 135,000. Find Acl. %3D R 220 k
2. For the below figure - a) Derive the output and minimize the output function using Karnaugh map b) Draw the wave form of output if B
Consider the circult given below a) Identify the circuit with details b) Find the Q-point O Find Vs,Vs Vo, Vos and Vas d) Find the RMS output voltage and draw it In the same graph- with Input e) Comment on the output signal if the input increases to Vinp=20V V 18 V 2.7 w - 10 MA atanm - - 6 V C 100F -0.3 F 1.5 MD - 130 F 220 11
Brief explanation of kalman filter
At what frequencies will the output waveform be half-wave rectified? A full-wave rectified?
The clamping circuit clamps or shift the input sinusoidal signal up or down. F
A triangular pulse waveform is shown in figure by waveform analysis draw the component function and write the corresponding equation of the component function. ( Proper steps)