Design the required rectangular sedimentation tank(s) for a water treatment plant given the following information: • . Flow rate: 37, 900 m³/d Detention time: 3.1 hours Surface loading rate (overflow rate): 38 (m³/d)/m² L = 4 W Weir loading rate: 240 m³/m/day. The weir should be designed to achieve the geometry given below. Find the value of Width of Basin (W), Length of Basin (L), Total Weir Length and Value of "b" below. (W-2) 00-1
Q: A weir has been constructed across a concrete-lined channel with a rectangular cross-section (base…
A: Step 1:Step 2:Step 3: Step 4:
Q: Compute the combined effects of curvature and refraction on level sights of 20, 200, 400, 800, and…
A: Step 1: Formula used.The combined effects of curvature and refraction on level sights is given as:-…
Q: Identify and describe two cases where a distributed load can be found in the real world: one as a…
A:
Q: Thumbs up will be given. Please write the complete solutions in 4 decimal places legibly. Solve…
A: Sure, I can solve problems that involve solving for reactions at supports using the double…
Q: Multiply out the series for exp(uz/2) and the series for exp(-u/2z) and then collect equal powers of…
A:
Q: Questions 6&7. If you use a source please let me know which one
A: References:https://www.axeonwater.com/blog/reverse-osmosis-vs-ion-exchange/#:~:text=Both%20reverse%2…
Q: Q2) find the relation error use the Simpson's 1/3 rule to approximate the definite integral. use…
A:
Q: Draw the shear & moment diagrams beam AB. Also find the PDF "What makes a complete V&M diagram?" on…
A: Step 1:
Q: 012 70 100 50 30 10 30 10 60 5)
A:
Q: AMPAD A 67°17 ل P THE FOUR SIDED CLOSED TRAVERSE HAS THE FOLLOWING ANGLES & DISTANCES. A 51°23' B…
A: Please thumbs up for giving me a good ratings thank you so much.
Q: The segment of road passing over the crest of a hill is defined by the parabolic curve y = 0.4x -…
A: The objective of the question is to find the normal pressure on the wheels of the car when it is at…
Q: = 14.6 In Figure P14.6, let H₁ = 2.5 m, H₂ = 4.5 m, y₁ = 16.8 kN/m², 9=0, 34°, c = 0, y2 = 22 kN/m³,…
A:
Q: A haul road from a borrow pit to the fill has an adverse grade of 3% and has rolling resistance of…
A: The objective of the question is to calculate the effective grade for the haul road. The effective…
Q: Problem 3 The pipes shown in the system are all concrete. With a flow of 25 ft³/s (or cfs) of water,…
A:
Q: How can a safety performance function be used for safety improvement analysis?
A: Safety performance function can be used to predict the crashes and other information relating to it.…
Q: Determine the surface dimensions and number of filters required to treat 23,000 m³/d if the rate of…
A: Step 1:Given: Flow rate to be treated = 23,000 m³/dMaximum filtration rate = 8 gpm/sfConvert the…
Q: J STEEL COLUMN L = 20' 9.13 What is the most economical W8 column for Problem 9.12?
A: Step 1:Step 2:
Q: Problem 2. A reverse osmosis membrane has a kw values of 2.5-10 L/(m²-s-bar) and an average ks value…
A: Step 1:
Q: Problem 1: Parshall Flume Calculate the flow through the flume with the following conditions: Given:…
A:
Q: A wooden column with a square cross-section of length 4250 mm is pinned at both ends. The Young's…
A:
Q: 2. Each block has a weight of 400 lb. Determine how far the force P can compress the spring until…
A:
Q: Problem 2: Select open web steel joists for a roof system with a span length of 44 ft. The roof…
A: Step 1:Step 2:Step 3:
Q: See the image below. b = 120 mm, t = 15 mm, H = 400 mm, tw = 8 mm. Calculate the slenderness of this…
A:
Q: Solution
A: Step 1:Step 2:Step 3:Step 4:
Q: The rectangular reinforced concrete column shown is part of a special moment frame in a region of…
A:
Q: i) With the aid of a diagram, explain the significance of transverse drains. ii) You see an…
A: Step 1:Step 2:
Q: Hint #3: All of the material separated out by the magnet (extract) goes to the roll crusher. All of…
A: Here is the step by step solution of the whole problem with best of my knowledge and understanding…
Q: Given the load diagram below, Determine the maximum positive moment in kN-m. Find the minimum height…
A: Step 1: solve reactions Step 2: Draw shear diagram Step 3: Determine maximum shear Step 4: Use V =…
Q: A beam carrying an allowable actual moment of -38 KN- m is reinforced as shown. If the the concrete…
A: Key references: Hamrat, M., Bouziadi, F., Boulekbache, B., Daouadji, T. H., Chergui, S., Labed, A.,…
Q: When designing the Screens for a WTP or WWTP, what are the three major design parameters
A:
Q: Determine the internal normal force, shear force, and moment at point D in the beam. Ans: AD = -1350…
A: Step 1: Step 2: Step 3: Step 4:
Q: Structures, flexibillity method. I have been working on this and dont seem to be geeting it right,…
A: The beam is illustrated as: According to the Flexibility Method, the sum of all deflections due to…
Q: A 111- resistor, a 0.150-uF capacitor, and a 5.77-mH inductor are connected in series to a generator…
A:
Q: Find bar CE
A: Step 1:Step 2:Step 3:If you understand the answer then like it, otherwise ask for clarification
Q: The beam is subjected to the distributed loads shown and supported by a rocker at C and a pin at A.…
A:
Q: The two steel shafts, each with one end built into a rigid support, have flanges attached to their…
A: Step 1: Step 2: Step 3: Step 4:
Q: ENVIRONMENTAL ENGINEERING Practice Question (a) List the three categories of use that account for…
A:
Q: Q12 1 Point 12.A soil sample has a total unit weight of 19.5 kN m 3. a dry unit weight of 16.4 kNm3…
A: Given:Wet/Moist Unit Weight (γ)= 19.5 kN/m3Dry Unit Weight (γd) = 16.4 kN/m3Specific Gravity (Gs) =…
Q: Level 1- Class D Submission Date: 15/04/2024 Q1: Determine the internal forces in all members of the…
A: Step 1: Solve for reactions, sum up forces horizontal and vertical at joint C. Step 2: Sum up…
Q: SOLVE USING RANKINES THEORY
A: Factore of Safety against Overturning = 4.07Factore of Safety against Sliding = 1.78Factore of…
Q: Consider a simply-supported rectangular plate with sides of a = 0.8 m, b = 0.6 m, and thickness of h…
A: Based on the image you sent, which appears to be a psychrometric chart, we can determine the…
Q: How do evaluation methods of historic building materials and assemblies contribute to the broader…
A: The objective of the question is to understand the importance of evaluation methods of historic…
Q: If the material is a dry clay, which of the following is likely to weigh the least? one bank cubic…
A: The question is asking us to determine which of the three given volumes of dry clay would weigh the…
Q: For the beam in Figure 1, use the method of virtual work to determine the slope at points B and C,…
A: Step 1:Step 2:Step 3:Step 4:Step 5:Step 6:Step 7:Step 8:
Q: Problem-5. For the beam shown, draw the influence lines for the shear and bending moment at point B.…
A: The objective of the question is to draw the influence lines for the shear and bending moment at…
Q: Determine whether the block shown is in equilibrium and find the magnitude and direction of the…
A: Step 1: Draw the FBDStep 2: Compute for the normal…
Q: Thumbs up will be given. Please write the complete solutions in 4 decimal places legibly. Solve…
A: Step 1: Step 2: Step 3: Step 4:
Q: The tension member shown in the figure below contains screw holes 7/8". For what step, S, will be…
A:
Q: List 10 key factors of congestion mitigation that may influence freeway mobility performance.
A: Approach to solving the question: Detailed explanation: 1. ROAD WORKS - work done in constructing or…
Q: A 20 kg box is placed on an incline plane against a stop as shown below. A flexible cable is…
A: Step 1:Step 2:Step 3:Step 4:
Step by step
Solved in 2 steps
- A rectangular channel carries a discharge of 45 m/s. The median particle diameter of the suspended load is 2.8 mm. Use channel conveyance factor of 600 and u = 1.14 104). Determine the following: a) Chezy's Coefficient and D-W friction factor b) Bed slope (S.) required to be provided c) Critical flows: depth, velocity, slope and specific energy d) Normal flows: width, depth and mean velocity e) Reynolds number and Froude number and state their status f) Maximum specific discharge and critical slope g) Comment on the applicability of Manning's EquationRead the question carefully and give me both a&b right solutions. A 1.3-m wide rectangular channel with a bed slope of 0.00019 has a depth of flow of 0.8m. Manning’s roughness coefficient is 0.017. (a) Can Manning’s equation be applied to this system (i.e., is the flow fully turbulent)? (b) Regardless of the answer to part a, determine the steady uniform discharge in the channel.1. Design a pipe culvert using the following data. Also, draw the longitudinal section of the culvert. Discharge in the stream: 4 m/s Road top level: 106 m Road bottom level: 101.5 m Road width: 7.5 m with 1 m wide shoulders Density of the soil at site: 18 kN/m3 Loading: IRC Class A C. = 1.8
- A concrete-lined trapezoidal channel has to be constructed to carry a discharge of 500 cfs. Design the channel. Assume that the following values were fixed based on the site conditions: • Bed slope = 0.002 • n = 0.015 • Side slope, z = 1 (vertical):1.5 (horizontal) • b/y ratio = 2.0. Refer to the following channel cross section. Normal depth is 3.0 feet. (a) What is the cross-sectional area of flow? (b) What is the wetted perimeter? (c) What is the hydraulic radius? 3.0' 1.5' 1.5' 8) noio222013 (6) -5.0'- JadW (d) O Cengage Learning 2014A- Proportional flow weir is used to keep constant horizontal velocity in: 1. Primary sedimentation tank 2. Areation tank 3. Grit removal chamber 4. Screen Hve
- Design a weir according to the following data: Channel width = 6 m. Flow discharge = 5 m³/s. Upstream water depth = 1.5 m. Adopt Ca=0.65. 1A circular settling basin is anticipated to receive a flow of 3.5 MGD. The tank is to be designed to have an overflow rate of 800 gpd/ft2. The depth is to be 11 ft. Determine the diameter of the basin (in feet). ? What length of weir (ft) is required to achieve a weir loading of 15,000 gpd/ft show all workIn 28.5 secs, 35,579 L of water is collected. The length of the rectangular weir is 2.15 m, the crest is 450 mm high from the channel bed and it should maintain a constant head of 275 mm. Determine the coefficient of discharge. Assume there is head loss. show your complete solution
- In culverts design under outlet control, if the desired Manning coefficient is 0.02. The corrected culvert length of the culvert would increase. * False True For the logarithmic normal distribution fitting in the flood forecasting. The discharged should be ranked in a logarithmic order. * False O True For Manning's Equation, the letter A/P represents the hydraulic radius. * False O TrueA Circular primary sedimentation tank for a municipal WWTP is to be designed for an average flowrate 6400 m³/s, depth is 3 m, overflow rate 35 m³/m².d and weir loading is 180 m³/m.d. Determine diameter of tank, detention time and weir length. If unsure let others do. Don't do wrong and waste my questionQ#1(a) Water flows over a rectangular weir 3m long. The height of water surface over the weir is 1m. Calculate discharge over the weir by: Simple formula Francis’ formula Take Cd=0.62 and velocity of approach=2m/sec. Find the difference between the two discharges. (b) What is meant by “Hydraulic coefficient”? Explain different types of hydraulic coefficients. (c) What is a “Cippoletti weir” ?Prove that the side slope of a Cippoletti weir is 1:4.