Determine the amount of water that can be delivered by a sprinkler head having a 3/4" in orifice with a 13.7 k-factor and installed in an automatic sprinkler system having a 35 psi residual pressure. Example 11.1What is the flow rate of a sprinkler with a standard 1/2-in. orifice (K = 5.5) with 20 psi residual pressure?SolutionFlow rate Q = 5.5 x √/20 = 5.5 x 4.4724.6 GPMExample 11.2What is the flow rate of a sprinkler with a 3/4-in. orifice (K = 14) with 65 psi?Solution=Flow rate Q = 14 x √√65 = 14 x 8.1= 112.9 GPM The flow rate of a sprinkler depends on the size of its orifice and the residual pressure of the water supply. The flow rate is calculated from the fundamental fluid flowformula,(11.1)whereQ = flow rate, GPMQ = KX √PK = flow constant, per unit; varies from 1.3 to 1.5 for a 1/4-in. orifice, 5.3 to 5.8 for a 1/2-in. orifice, to 13.5 to 14.5 for a ³/4-in. orificep = pressure, psi (residual pressure at rated flow)

The Head of orifice = 3/4"Automatic sprinkler system (P) = 35 PsiFlow factor (K) = 13.7

Answered: Determine the amount of water that can…

Determine the amount of water that can be delivered by a sprinkler head having a 3/4" in orifice with a 13.7 k-factor and installed in an automatic sprinkler system having a 35 psi residual pressure

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

11. A 350 mm by 150 mm venturi meter is installed in a vertical pipeline carrying water as shown in the figure. The flow is upward through the meter. A differential manometer containing carbon tetra-chloride (sg=1.5) is attached to inlet and throat. The difference Z in gage level is 700 mm. Neglecting the head loss, compute the discharge of the venturi meter 350 mm 150 mm 300 mm 700 mm
Problems for Practice 7. A fluid flows at 0.002 m³/s through a 150 - mm diameter pipe. Determine whether the flow is laminar or turbulent if the fluid is: a. Air (v = 1.48 × 105 m²/s) b. Water (μ = 8.90 × 104 Pa-s) Mercury (u = 1.53 × 10-3³ Pa-s) d. Glycerin (v = 1.18 × 10³ m²/s) Gasoline (v = 4.06 × 10-7 m²/s) C. e. Manila FB: @ReviewinnovationsOfficial
Question 4 Quèstion 4 1 points Application of orificemeter is O 1. Measure pressure difference O 2. Measure mass flow rate O 3. Measure pressure difference O 4. Measure volume flow rate
3. IN THE FIGURE SHOWN, THE 50-METER PIPE IS 60 MM IN DIAMETER. THE FLUID FLOWING HAS MASS DENSITY OF 920 KG/CU.METER AND DYNAMIC VISCOSITY OF 0.29 PA-S. THE PRESSURE IN THE ENCLOSED TANK IS 200 KPA GAGE. DETERMINE THE FOLLOWING(ƒ =0.0225). A. THE AMOUNT AND DIRECTION OF FLOW B. THE VELOCITY OF FLOW IN THE PIPE. C. THE REYNOLDS NUMBER OF THE FLOW H= 12 m L=50 m
The table below show data collected from flow rate measurement experiment that was carried out using the hydraulic bench. Fill up the blank cells in the right column of the table (pay attention to units) Time (S) Volume (L) Flow rate (m/s) 10 8.5 7 11 Qverage =
A fluid flows at 0.002 m³/s through a 150- mm - diameter pipe. Determine whether the flow is laminar or turbulent if the fluid is: a. Air (v = 1.48 x 10³ m²/s) b. Ans. laminar Water (p = 8.90 × 10^ Pa-s) Ans. turbulent Mercury (u = 1.53 x 10³ Pa-s) Ans. turbulent Glycerin (v = 1.18 x 10³ m²/s) d. e. Gasoline (v = 4.06 x 107 m²/s) Ans. laminar Ans. laminar
A flow rate measuring device is installed in a horizontal pipe through which water is flowing. A U-tube manometer is connected to the pipe through pressure taps located 3 in. on either side of the device. The gage fluid in the manometer has a specific weight of 112 lb/ft3. Determine the differential reading of the manometer corresponding to a pressure drop between the taps of 0.5 lb/in². h = ft
c) The orifice flowmeter shown in Figure 4 is used to obtain the flowrate of oil inside a conduit. The diameter of the orice, d is one third of the pipe diameter, D with pressure difference recorded as 25 kPa. The pipe diameter D is 6 cm, discharge coefficient Ca, is 0.60, Bis the ratio of orifice diameter to pipe diameter and Oilspedific gravity, SG is 0.95. If the h is 7 cm, i. Calculațe the vollime flowrate of oil inside the conduit. ii. Determine the mass flowrate of oil inside the conduit. iii. Explain why the discharge coefficient Ca, for the orifice meter is higher compared to the venturi and nozzle meters. D=6 cm d Figure 4
(c) Venturi-type flowmeter shown in Figure 5 is used to obtain the flowrate of oil inside a conduit. The diameter of the venturi, d is one third of the pipe diameter, D. The pipe diameter D is 6 cm, pressure difference reading AP, is 25 kPa, discharge coefficient Ca, is 0.98, Bis the ratio of venturi diameter to pipe diameter and oil specific gravity, SG is 0.95. i) Calculate the volume flowrate of oil inside the conduit. ii) Determine the mass flowrate of oil inside the conduit. iii) Explain why the discharge coefficient Ca, for the ventury meter is higher compared to the nozzle meter. 2(P – P.) V. ventury AP oil d Figure 5
Q.15 Water is flowing through two pipes one of 10 mm diameter and second of 5 mm diameter and both are discharging in 12 mm diameter pipe. The rate of flow in 10 mm diameter is 1.0 c.c./s. If the Reynolds number of 12 mm diameter pipe flow is 4000, determine the rate of flow in 5 mm diameter pipe. Consider kinematic viscosity equal to 6.5 x 10-7 m²/s.
Water is flowing from point A to point B in the system shown in the figure. All the corresponding length and diameter of each pipe is shown. Assuming that each pipe has n=0.011 and head loss from point A to B is 30m, determine the a) discharge at pipe 1 b) discharge at pipe 3 c) discharge at pipe 5
A venturimeter is: efully designed pressure difference is a measure of flow volume rate in a pipe. Using Bernoulli's equation for steady, incompressible flow with no loses, show that the flow rate is related to the manometer reading 2gh(p_ - p) h by Q =- where pm is the density of the manometer fluid.