Answered: For a given load, Vms=110Z85°V,…

For a given load, Vms=110Z85°V, Ims=0.4Z15°A. Determine: a) the complex and apparent powers b) the real and reactive powers c) the power factor and the load impedance

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.13MCQ

See similar textbooks

Related questions

Q: 2. Three impedances Za , Zb and Zc are connected in parallel. If at 60 hz , Za = 3 + j4 , Zb = 4 –…

Q: A balanced star-connected source has phase voltage Vab = 416 230° V and a positive phase sequence.…

Q: shows a balanced three-phase source supplying a balanced three-phase load. Referring to the picture…

Q: For the following circuit, find (a) the load impedance required for maximum average power transfer…

Q: (a) the full load efficiency at unity power factor;

Q: For a transmission line with 50 ohm impedance, plot the normalized impedance for the following…

Q: For the circuit shown below, all the voltage values are given in rms. The apparent power of the…

A: The given circuit is: All voltages values are given in RMS. Apparent power of three phase load,…

Q: A three-phase circuit has two parallel connected balanced loads. The first is a balanced delta load…

A: The solution is given below

Q: For the circuit in the figure, Determine the complex power delivered to the three-phase load. The…

Q: Determine the impedance value per phase of an inductive load represented by R+jX in a circuit. The…

A: Given: Star connected balanced load. Q=5933.03 VARcosϕ=0.82 lagV=220∠0° V

Q: Apply single-phase equivalency to determine the line currents in the Y-Δ network in the figure…

Q: A balanced three-phase source having a line voltage of 208-Vrms is supplying two parallel-connected…

A: The solution is given below

Q: 4. Three identical impedances ZA = 9430°N are delta-connected to 220V source by three identical line…

A: The solution is given below

Q: A balanced three-phase source having a line voltage of 208-V rms is supplying two parallel-connected…

A: The solution is given below

Q: A balanced three-phase source with a 208 V rms (line-line) is delivering power to a balanced…

A: The solution is given below

Q: a transmission line has an impedance of 4 12 Ohms/phase, Find the per-unit impedance of this line on…

Q: (c) The phase voltages across a certain load are given as, Va = (176 – j132) V V, = (-128 – j96) V…

A: As per the rules we can answer only one question, please post the remaining question as the separate…

Q: Q5: For the circuit in the figure, Determine the complex power delivered to the three-phase load.…

Q: A three-phase system having an rms line voltage of 141.4V is connected to a delta balanced load with…

A: Given data, Line voltage VL=141.4 V Load impedance ZL=15∠300 Ω

Q: The average power on the Z1 impedance is 8kw and the power factor is 0.8. This power factor is a…

A: In this question , we will find apparent power of equivalent load..

Q: Note: It is expected from student to develop impedance matrices ofthree phase power system. Develop…

A: Given: Pwer sytem network Z-bus can be build by the 4 types of modification:Type-1: New to…

Q: 2. In an unbalanced system, the phase voltages are: Vna = 13240 What is the line to line voltage…

A: In this question, Unbalanced voltages are given. Find the line voltage VCB ? VCB = Vnb -Vnc

Q: A balanced three phase A- connected load has a line voltage of 2500 Vrms , and absorbs an average…

A: The complex power in an AC system is defined as the product of rms value of applied voltage and…

Q: Find the RMS line voltage VL at the source of the circuit. As shown the RMS load phase voltage is…

Q: 14. Consider this power distribution system to a customer: Transmission line current Power company V…

A: The solution is given below

Q: Convert the wye-connected load to its delta equivalent. What is the per phase impedance of the delta…

A: Given

Q: Problem 12: For the network show below, find: a) The total impedance Z b) The value of C in…

A: As per the guidelines of Bartley we supposed to answer first three subpart only for solution of…

Q: Given a balanced three-phase system - Δ-connected load with an impedance of 12 + j9 Ω/ϕ -…

A: Power system problem Look below for the detailed explanation..

Q: A balanced star-connected source has phase voltage Vab 416 230° V and a positive phase %3D sequence.…

A: We are authorized to answer one question at a time since you have not mentioned which question you…

Q: A balanced three-phase delta connected source supplies to a balance three-phase star connected load,…

Q: Determine the phase sequence of the set of voltages Van = 200 cos(ωt + 10°), Vbn = 200 cos(ωt −…

A: to determine the phase sequence of the set of voltages Van = 200 Cos (ɷt+10˚) V bn = 200 Cos…

Q: A Q.20: For the circuit shown, let Z,=Z2=Z3=60Z30°Q are phase impedances, and the phase voltage be a…

Q: A 30-Ω resistor, a 15-Ω inductive reactance, and a 12-Ω capacitive reactance are connected in…

Q: An unbalanced delta-connected load is supplied from a 400-V, 3-ph, delta-connected alternator…

A: Delta connection is a mesh type connection made to the electrical apparatus and the three phase…

Q: In the circuit below, the voltage between phase is 230Vrms. Find the phase current, line current, P,…

A: As per the guidelines of Bartleby we supposed to answer first three sub part of the question for…

Q: A balanced three-phase source having a line voltage of 208-V rms is supplying two parallel-connected…

A: In this question, Line voltage VL = 208V Supplied to the two parallel loads. Impedance of each…

Q: A 3-phase, 208V system supplies a delta load with impedances ZAB = 150 235°, ZBC %3D - 12Ω /20ο and…

A: In this question, Three phase Delta unbalanced impedance is given. Find the line currents, active…

Q: 5Ω j3 N a 20 /0° 20 ΩΣ -j6 Ω V b (a) For the circuit shown above, determine the impedance Zı that…

Q: A three-phase balanced source is energizing a delta-connected load. The phase voltage of the source…

Q: In a balanced Y-Delta connection the magnitude of the line voltages VL = 1500 V (rms), the load…

Q: A balanced star-connected source has phase voltage Vab = 416 230° V and a positive phase %3D…

Q: a) A three-phase star connected alternator supplies a star connected load. Given the supplied single…

A: The given system is balanced system.

Q: Find the RMS line voltage VL at the source of the circuit. As shown the RMS load phase voltage is…

A: 3 phase balance load connected to balance system Voltage across load 100V Then find source…

Q: (d) In a balanced three-phase wye-wye (Y-Y) system, V;< = 200210° Vrms. The load impedance per phase…

Q: A parallel pair circuit of two impedances Z(1)= 11 + j 23 and Z(2)= 6 - j 13 is supplied with an AC…

Q: Given at the load: What are the real and reactive power and power factor at the load? Exclude the…

A: We need to find out the power of given voltage and current

Q: For the given circuit calculate the maximum power that can be transferred from the circuit to the…

A: In this given circuit, Find the maximum power transfer to the load. For maximum power transfer…

Q: 2. A voltage source of v(t) = 340sin(2n60t) V is applied to a nonlinear load, resulting a current…

Q: vs 60 kVA at lagging PF of 0.8, while load 2 draws 26.667 ume no line resistance and Vab-440L 30°…

A: In this question given 2 loads ...We have to find out total power dream by loads , phase currents…

Q: For a 3-phase Y-connected balanced load, at the terminals the following are given: Vea = 4804170°V…

A: It is given that: Vca=480∠170°VIb=40∠-130°A

Concept explainers

Analog to Digital Converters

The analog-to-digital converter (ADC) allows circuits controlled by microprocessors, Arduinos, Raspberry Pi, and various reasonable digital circuits to be connected to the real world. In the real world, analog signals have a continuous stream of information from a variety of sources and sensors capable of measuring sound, light, temperature, or movement, in addition to the many digital systems that interact with their environment by measuring analog signals from those transducers.

Question

question is attached in image

For a given load, Vms=110Z85°V, Irms=0.4Z15°A. Determine:
a) the complex and apparent powers
b) the real and reactive powers
c) the power factor and the load impedance

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
a. Find the total admittance and impedance in polar form b. Draw the admittance and impedance diagram c. Find the voltage E and currents IR , IL , and Ic in phasor form d. Draw the phasor diagram of the currents Is, IR, IL and IC, and the voltage E. e. Verify Kirchhoff’s current law at one node f. Find the average power delivered to the circuit g. Find the power factor of the circuit, and indicate whether it is leading or lagging. h. What happened if R= 10 Ω
For the given circuit: a.Find the total impedance ZTin polar form. b.Find the current I and the voltages VRand VLin phasor form. c.Find the power factor of the circuit, and indicate whether it is leading or lagging.
The active and reactive powers of an inductive circuit are 60W and 80VAR respectively. The power factor of the circuit is ___. a. 0.8 lagging b. 0.75 lagging c. 0.5 lagging d. 0.6 lagging
For the system in the figure: Find the total average power, total reactive power, total apparent power, and total power factor. Find the current Is (in phasor form). If the loads can be modeled as a resistance in series with a reactive element (capacitor or inductor), find the impedance of each load. Confirm the result of part B using the input voltage and the result of part C. ..
A load is rated at 440V(rms), 7.5A(rms) and 3.3KW when connected to a 50HZ source. Find the load impedance.
a. Find the total impedance ZT in polar form b. Draw the impedance diagram c. Find the current I and voltages VR , VL , and Vc in phasor form d. Draw the phasor diagram of the voltages E, VR, VL and VC, and the current I. e. Verify Kirchhoff’s voltage law around the closed loop. f. Find the average power delivered to the circuit g. Find the power factor of the circuit, and indicate whether it is leading or lagging.
A. Find the total impedence Zt in polar form. B. Draw the impedence diagram. C. Find the current and voltages Vr,VL and VC in phasor form. D. Draw the phasor diagram of voltage E,VR,VL and VC and the current I. E. Verify kirchoff's voltage law arround the closed loop. F. Find the average power delivered to the circuit. G. Find the power factor of the circuit, and indicate whether it is leading or lagging. H. What happened if Xc=2ohm? Please explain.
An electric load consists of a resistor, a capacitor and an inductor connected in series. The total impedance of the load is connected across 240430° V, compute the following: a. The load impedance b. The source current in polar form c. The phase shift between the current and the voltage d. The power factor of the load e. The real power of the circuit f. The reactive power of the circuit 20 mH 50UF 240430° 314rad/s W =
lši vl pir:10 Expert Q&A + 1. For the circuit in Figure: a. Determine I, VR, and Ve in phasor form. b. Calculate the total power factor, and indicate whether it is leading or lagging. c. Calculate the average power delivered to the circuit. d. Draw the impedance diagram. e. Find the voltages VR and Vcusing the voltage divider rule and compare them with the results of part(a) above. + Uc - + Ug - 30 2 L = 0.2 H L =0.2 H C = 4 µF e = V2(20) sin(377t + 40°) Expert Answer Home Search More II
A Z load draws 12kVA from a 120 V-rms sinusoidal source with a back power factor of 0.85. Find the average power and reactive power supplied to the load.