For the four bus system as shown in Fig. Determine the fault current when the fault takes place at bus no.3 with fault impedance Zf=j0.32 p.u. The Subtransient reactance of the generators and positive sequence reactance of other elements are given. Assume pre fault Voltage Eth= 120° p.u Generator X = j0.16p.u; Transmission line X = j0.26p.u; Transformer X j0.34p.u !! %3D %3D 十章1章 Y글 스 A Zth in p.u Fault current I in p.u Fault Current contribution by the Generator G2 (IG2) 00000 000

For the four bus system as shown in Fig. Determine the fault current when the fault takes place at bus no.3 with fault impedance Zf=j0.32 p.u. The Subtransient reactance of the generators and positive sequence reactance of other elements are given. Assume pre fault Voltage Eth= 120° p.u Generator X = j0.16p.u; Transmission line X = j0.26p.u; Transformer X j0.34p.u !! %3D %3D 十章1章 Y글 스 A Zth in p.u Fault current I in p.u Fault Current contribution by the Generator G2 (IG2) 00000 000

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter8: Symmetrical Components

Section: Chapter Questions

Problem 8.36P

See similar textbooks

Similar questions

b) A fault occurs at bus 4 of the network shown in Figure Q3. Pre-fault nodal voltages throughout the network are of 1 p.u. and the impedance of the electric arc is neglected. Sequence impedance parameters of the generator, transmission lines, and transformer are given in Figure Q3, where X and Y are the last two digits of your student number. jX(1) j0.1Y p.u. jX2)= j0.1Y p.u. jXko) = j0.1X p.u. V₁ = 120° p.u. V₂ = 120° p.u. (i) (ii) 0 jX(1) = j0.2 p.u. 1 jx(2) j0.2 p.u. 2 jX1(0) = j0.25 p.u. jXT(1) jXT(2) 종 3 j0.1X p.u. JX3(1) j0.1Y p.u. j0.1X p.u. JX3(2) j0.1Y p.u. jXT(0) j0.1X p.u. JX3(0)=j0.15 p.u. 0 = x = 1, jX2(1) j0.2Y p.u. V₁=1/0° p.u. jX(2(2) = j0.2Y p.u. jX2(0) = j0.3X p.u. = V3 = 120° p.u. Figure Q3. Circuit for problem 3b). For example, if your student number is c1700123, then: y = 7 = = jXa(r) = j0.13 p.u., jXa(z) = j0.13 p. u., and jXa(o) = j0.12 p. u. Assuming a balanced excitation, draw the positive, negative and zero sequence Thévenin equivalent circuits as seen from…
The sample large power system network data's are given below, The total number of buses is 5 Three-phase short circuit fault subjected at the bus 5 The initial voltage of the faulted bus is 1.0 p.u The Zbus matrix element Z55 is 0.704 p.u Fault impedance Zf= 0.33 p.u Fault current (If )in p.u ..........
Q3: - A three-phase fault occurs at bus-1 of the network shown in figure below. The pre-fault voltage is 1.05 PU and the pre-fault load current is neglected. (45%) i) determine the bus impedance matrix. ii) calculate the sub-transient fault current and the contribution to the fault current from the transmission line. T1 T2 T.L j0.1 PU 10.1 PU j0.105 PU G jXdg j0.15 PU M jXdm $0.2 PU
b) The one-line diagram for a simple power system is given in Figure 1(b). į. Draw the impedance diagram of the system. i. Construct the bus admittance matrix, Xeus and bus impedance matrix, Zous of the system. I. Evaluate the fault current, bus voltages and line current during the flow when a balanced three-phase fault occurs on bus 1. bus 1 bus 2 j65 N G G 25 MVA 25 MVA 13.8 kV 15% 13.2/69 kV 11% 25 MVA 69/13.2 kV 11% 15 MVA 13 kV 15% Figure 1(b) m
b) A fault occurs at bus 2 of the network shown in Figure Q3. Pre-fault nodal voltages throughout the network are of 1 p.u. and the impedance of the electric arc is neglected. Sequence impedance parameters of the generator, transmission lines, and transformer are given in Figure Q3, where X and Y are the last two digits of your student number. JX20 /0.1X p.u. jXa2) 0.1X p.u. JX20 j0.2Y p.u. V,= 120° p.u. V, 120° p.u. V, 120° p.u. jX4-70.2X p.u. jX2 j0.2X p.u. jX o 0.2Y p.u. jXncay J0.25 p.u. jXna J0.25 p.u. 3 jXno0.3 p.u. jXTu) /0.2Y p.u. jXra j0.2Y p.u. - j0.2Y p.u. Xp-10.1X p.u. jXa j0.1X p.u. jXp0)- j0.05 p.u. 0 Figure Q3. Circuit for problem 3b). For example, if your student number is c1700123, then: jXac1) = j0.22 p.u., jXac2) = j0.22 p.u., and jXaco) = j0.23 p. u. X-2 Y=8 (iv) Determine the short-circuit fault current for the case when a phase-to- phase fault occurs at bus 2.
A hydro powered 50 MVA generator, with a synchronous reactance 0.33 p.u., delivers 40 MW over a transmission line of 0.15 p.u. reactance to an infinite system. A 3-phase short circuit transient fault occurs on the busbar between the generator and transmission line. Given that the generator emf is 1.4 p.u. prior to and during the fault and all reactances are to a 50 MVA base: Sketch the single line schematic diagram of the system. Determine the maximum load angle the generator can swing to without losing stability. i) ii) iii) iv) Sketch the corresponding power-angle curve for the system showing the accelerating and decelerating areas. Calculate the critical clearing angle of the system to keep its stability.
In a 7-bus system, the double line fault is occurred at bus -5. During fault the positive sequence potential difference between the bus-4 and bus-1is found to be 0.0175. what is the line impedance which is connected between bus-4 and bus-1 if the current flowing through transmission line is -j 0.148? Select one: O a. -jo.182 O b. +j0.1182 O c. -jo.1182 O d. +j0.182
The LLLG fault occurs at bus-6 with pre-fault voltage as 1.05 p.u. If the positive sequence impedance at bus-7 is j0.35 and positive sequence current is -j1.250. Find value of positive sequence voltage at bus-7.
The one-line diagram of a simple three- bus power system is shown below. Each generator is represented by an emf behind the transient reactance. All impedances are expressed in per unit on a common 100 MVA base. Determine the fault current during a fault when a balanced three-phase fault occurs on Bus 1. Use the Thevenin Theorem approach. j0.2 Hint j0.1 J0.8 j0.2 RRRR. R RRR j0.4 j0.4,5 RR. R RRRR. R.RRRRR RRR 2.84xj p.u. 6.25xj p.u. -4.58xj p.u. -6.25xj p.u. 5.10xj p.u.
The fault current level of a circuit breaker used in a transmission line with phase voltage 2.2 kV and breaking capacity 60 MVA is ......................kA. Complete the answer.
The system values are given below. The bus 1 voltage after fault = 1.5 p.u The bus 2 voltage after fault = 1.2 p.u The line admittance between bus 1 and bus 2 (Y12 ) is = 0.8 p.u The post fault current current flow between bus 1 and 2 is ..............
ns. or A 25 MVA, 13.2 KV, alternator with solidly grounded neutral has a sub transient reactance of 0.025 p.u. The negative and zero sequence reactances are 0.35 and 0.1p.u. respectively. A single line to ground fault occurs at the terminals of an unloaded alternator; Determine the fault current and the line-to-line voltages. Neglect resistance. iont ctability