If the spring is compressed 60 mm and the coefficient ofstatic friction between the tapered stub S and the slider A isMSA = 0.5, determine the horizontal force P needed tomove the slider forward. The stub is free to move withoutfriction within the fixed collar C. The coefficient of staticfriction between A and surface B is μAB = 0.4. Neglect theweights of the slider and stub.NSE duk = 300 N/mww30°A-B

Answered: If the spring is compressed 60 mm and…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

*1-44. The 150-kg bucket is suspended from end E of the frame. If the diameters of the pins at A and D are 6 mm and 10 mm, respectively, determine the average shear stress developed in these pins. Each pin is subjected to double shear. 0.6 m 30% 1.2 m 0.6 m 0.6 m D OB A A W
CLASS WORK 1: 2m 2.5 2m 1.5m 4KN 5KN 6KN A. SOLVE THE VERTICAL REACTION IN THE ROLLER SUPPORT. 4 POINTS B. SOLVE THE RESULTANT OF HORIZONTAL AND VERTICAL REACTION AT HINGE SUPPORT. 6 POINTS C. SOLVE THE AXIAL STRESS IN MEMBER BE IF ITS CROSS-SECTIONAL AREA IS 300mm².25 POINTS 1m 3KN G H
The solid 34 mm diameter steel [E = 200 GPa] shaft supports two belt pulleys. Assume that the bearing at B can be idealized as a roller support and that the bearing at D can be idealized as a pin support. For the loading shown, determine: (a) the shaft deflection at pulley A. (b) the shaft deflection at pulley C. Assume P = 850 N, Q = 1050 N, LAB = 650 mm, Lgc = 1050 mm, Lcp = 1050 mm. A B C D P Answer: (a) VA = (b) vc = LAB LBC mm mm Q LCD
The gusset plate is subjected to the forces of three members. Determine the tension force in member C and its angle 0 for equilibrium. The forces are concurrent at point O. Take F = 8 kN. 9 kN F B. T
The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces shown, determined. Replace the two forces and couple by an equivalent couple M and resultant R at A. The cou 1.89 kN 0.41 m 1.47 m- 77 10.13 m 10.13 m A 570 N-m -x- 8 1.07 kN Answers: M = kN-m R = j) kN
The solid 38 mm diameter steel [E = 200 GPa] shaft supports two belt pulleys. Assume that the bearing at B can be idealized as a roller support and that the bearing at D can be idealized as a pin support. For the loading shown, determine: (a) the shaft deflection at pulley A. (b) the shaft deflection at pulley C. Assume P = 950 N, Q = 1150 N, LAB = 650 mm, LBC = 900 mm, LCD = 900 mm.
A reinforced rectangular beam with width b and effective depth d has 4.16 mm bars placed on 1 layer at the tension side. The beam has a stirrup with diameter of 10 mm. Use fe' = 28 MPa and fy = 420 MPa. Given: b= 350 d= 500| L- 6.85 Wd= 28 WI- 30.25 1. Calculate the nominal moment capacity of the beam. 2. Calculate the strain of the tension bars. 3. Calculate the strength reduction factor of the beam.
1 1.3-1 A hollow circular post ABC (see figure) supports a load P₁ = 7.5 kN acting at the top. A second load P₂ is uni- formly distributed around the cap plate at B. The diame- ters and thicknesses of the upper and lower parts of the 12 mm, dBc 57 mm, and = AB post are dB = 32 mm, TAB tBC = 9 mm, respectively. = t (a) Calculate the normal stress AB in the upper part o of the post. (b) If it is desired that the lower part of the post have the same compressive stress as the upper part, what should be the magnitude of the load P₂?
= The strut AB made from two bars (thickness of each bar = 0.50 in) is connected to a rectangular beam CD (b 0.80 in x h = 7.5 in) at joint B. The beam carries a concentrated load of 2750 lb at the end joint D. (a) determine the minimum diameter of the bolt at B if the shearing stress in the bolt is not to exceed 14000 psi. (b) determine the minimum diameter of the bolt at B if the allowable bearing stress in the bar plate is 20000 psi. Detail of joint B 3 ft (O с A 5 ft O B 6 ft D 2750 lb 3.75 in 3.75 in 0 in 0.80 Strut AB Beam CD (b Xh) Bolt (dmin) -0.50 in
8 F8-2. Determine the minimum force P to prevent the 30-kg rod AB from sliding. The contact surface at B is smooth, whereas the coefficient of static friction between the rod and the wall at A is p, = 0.2. B 4 m 3m
A set of 5-lb forces are applied to the handles of the pliers as shown. Simple pinconnections exist at pts. B, C, D, and E. Determine the compressive force developed on thesmooth cylinder at pt. A.
2. A tripod supports the load shown. Find the compressive force on member CD. Py =500 kN D Px = 50 kN 3m A RAY -- B 1m Ro REY Ra Roy

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS