In the system shown below, a jet of water-with diameter of 20 cm and a speed of 6 m/s-strikes astationary plate containing a hole of diameter 8 cm. A portion of the jet passes through the hole whilepart of it is deflected towards the perpendicular direction. Consider that the whole system is exposedto atmospheric pressure. Calculate the volumetric flow rate representing the portion deflected by theplate in cubic meters per second.

Answered: Image /qna-images/answer/035d5e05-449e-4d12-89a4-144ab296648c.jpg

Answered: ion. Consider tha v rate representi

Engineering

Civil Engineering

ion. Consider tha v rate representi

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the discharge through a pipe of diame ter 200 mm when the difference of pressure head between the two ends of a pipe 500 m apart is 4 m of water. Take the value of 'f' = 0.009 %3D
A right circular cylindrical tank container, 2m in diameter and 4m high is 1/2 full of water. When rotated about its vertical axis at the rate of 60 rpm:A.) How many meters will the water surface drop at the center of the vessel? B.) What is the pressure, in kPa, at the base of the container along the perimeter? C.) What is the volume, in m^3, of the paraboloid formed by the rotation of the vessel? (Show complete solution)
SITUATION 3. A 75mm DIAMETER ORIFICE DUNDER THE HEAD OF 5m DISCHARGES OIL WITH SG = 0.81. IF THE HORIZONTAL AND VERTICAL TRAJECTORY ARE 3.5m AND 5m, RESPECTIVELY, 3. DETERMINE THE COEFFICIENT OF VELOCITY Your answer 4. DETERMINE THE HEADLOSS IN THE ORIFICE * Your answer
A converging tube discharges water from a reservoir, into the air, at depth of 6 ft below the water surface. The diameter gradually decreases from 12 inch to 6 inch at the outlet. Neglecting friction, determine the rate of change in cubic feet per second.
A hemispherical tank having a radius of 2.5 m is filled with water to a depth of 1.8 m. If a solid sphere having a diameter of 1.6 m is placed on the bowl, determine how high will the water rise on the bowl. A. 176 mm B. 166 mm C. 171 mm D. 116 mm
A water jet of velocity 4.2 m/s and a cross-sectional area of 0.50 m2 strikes a curved vane, as shown above. 75% of the flow exits at the top and the remaining 25% from the bottom. The flow velocity in each exit stream has the same magnitude as the flow entering. The vane is stationary. The vane deflects the jet through an angle e of 54°, Determine the reaction forces Fy and Fy. Enter your answers in the order shown to two decimal places in units of kN.
A piezometer and a Pitot tube are tapped into a 4-cm diameter horizontal water pipe, and the height of the water columns are measured to be 26 cm in the piezometer and 35 cm in the Pitot tube (both measured from the top surface of the pipe). Determine the velocity at the center of the pipe, in m/s.
Situation 9. An orifice (D=100mm) located on a bottom of the cylindrical tank (D=2m, H=10m). Determine the time required for the tank to be emptied under the following conditions: Use Cd = 0.6 28. Tank subjected to pressure of 49.05 kPa A. C. D. B. 30. 1166 952 29. Tank is accelerated to downward at 4.905 m/s^2. A. 1166 B. 952 Tank is color blue. A. 1166 B. 952 C. D. 493 687 C. D. 493 673 493 687
1.28 Calculate the capillary rise in a glass tube of 2.5 mm diameter when immersed vertically in (a) water and (b) mercury. Take surface tensions o = 0.0725 N/m for water and o= 0.52 N/m for mercury in contact with air. The specific gravity for mercury is given as 13.6 and angle of contact = 130°.
In a pump that works with cold water, the discharge pressure gauge located 7.5 m above the axis of the pump marks a pressure height of 68 m.c.a. The vacuum gauge located 125 cm below the axis of the pump shows a relative pressure of 325 Torr. Due to the difference in diameters between the suction pipes The momentum is created a dynamic height of ½ m. Calculate the useful head of the pump?
Consider the hemispherical gate attached to a cylindrical buoy as shown in the figure. The thickness of and weight of the cable connecting the buoy and the gate are negligible. Which of the following is the volume above the hemispherical gate that is needed in the calculation of the vertical component of the resultant hydrostatic force acting on it? 4m Y? 3 m Select one: O a. cylinder up to the liquid surface O b. cylinder up to the liquid surface minus the hemisphere O c. cylinder up to the bottom surface of the buoy O d. cylinder up to the bottom surface of the buoy minus the hemisphere
ROVINCE c). If the viscosity is 0.0126 stokes, what is the equivalent kinematic viscosity in m2/s? 3. If the velocity of water is 8 m/s and the pressure is 140 kPa on the discharge side of a pump, a) what will be the head of the pump if the velocity is 4 m/s and the pressure is 90 kPa on the suction side of the pump? b) how much power is required to drive it if the diameter of the suction side is 600 mm? c) If the pump is rated at 120 hp, what is the efficiency of the pump neglecting energy losses in the system? STATE 1969