Laboratory Report 11 – Double Rodded Leveling Objective: To determine the elevation of BM12 using double rodded leveling. Discussion: (min of 5 sent) Instrument/equipment/ tools: 1 set of leveling instrument, 1 leveling rod Procedure: min 10 Sketch: prepare a schematic diagram(top view) for the data below, just use arbitrary route. Initial Table: Tabulation of data given below Solution: Final Table: Generalization: BM,, (elevation 1642.324) to BM12. In the following rod readings H refers to high route and L to low route: BS on BM11 = 7.342; FS on TP, H = 2.306; FS on TP,L = 4.107; BS on TP,H = 9.368; BS on TP,L = 11.162; FS on TP, H = 3.847; FS on TP,L = 5.111; BS on TP2H = 8.339; BS on TP,L = 9.619; FS on TP3H = 4.396; FS on TP3L = 5.448 ; BS on TP3H = 7.841; BS on TP3 L = 8.896; FS on BM12 = 3.329.

Laboratory Report 11 – Double Rodded Leveling Objective: To determine the elevation of BM12 using double rodded leveling. Discussion: (min of 5 sent) Instrument/equipment/ tools: 1 set of leveling instrument, 1 leveling rod Procedure: min 10 Sketch: prepare a schematic diagram(top view) for the data below, just use arbitrary route. Initial Table: Tabulation of data given below Solution: Final Table: Generalization: BM,, (elevation 1642.324) to BM12. In the following rod readings H refers to high route and L to low route: BS on BM11 = 7.342; FS on TP, H = 2.306; FS on TP,L = 4.107; BS on TP,H = 9.368; BS on TP,L = 11.162; FS on TP, H = 3.847; FS on TP,L = 5.111; BS on TP2H = 8.339; BS on TP,L = 9.619; FS on TP3H = 4.396; FS on TP3L = 5.448 ; BS on TP3H = 7.841; BS on TP3 L = 8.896; FS on BM12 = 3.329.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. Complete the profile leveling notes in Table 1. Show the arithmetic check and sample calculations of your work. Draw a neat sideview sketch showing the location of all stations and indicate on the sketch all of the numbers in your completed table. Page 1 of 4 I Table 1 Station BS [ft] HI [ft] IS [ft] FS [ft] Elevation [ft] BM1 8.92 423.15 TP1 5.79 6.27 0+00 8.83 1+00 7.13 2+00 7.96 2+70.5 8.81 2+76.2 8.39 3+00 6.34 TP2 8.16 5.99 4+00 7.77 5+00 7.47 5+55.0 4.19 5+65.2 6.65 6+00 7.29 BM2 6.76
INSTRUCTIONS: 1. Given below are the field notes (in meters) of a profile leveling work. 2. Construct the level notes, indicate elevation and show arithmetic check computation. Station BS HI FS Elevati Remarks on BM1 1.56 571.00 569.44 Benchmark Along profile line Along profile line Along profile line Along profile line Along profile line x-top of the rock Along profile line Along profile line Along profile line Along profile line Along profile line Along profile line Along profile line Along profile line Along profile line Along profile line Top of concrete pavement Along profile line Along profile line 1+000 1+100 1+200 5.67 2.00 3.40 1+300 1+400 TP1 3.00 6.70 8.00 3.0 566.00 1+500 1+600 3.00 1+700 1+800 1+900 4.10 5.40 7.00 5.00 3.50 2+000 2+100 2+200 2+300 2+400 2.80 2.00 0.60 0.80 2.10 ТР2 6.10 570.00 2+500 2+600 1.72 2.78
Q: A not to scale sketch illustrating a theodolite measuring the top of a shed shown below with the slope distance, horizontal and vertical angles, and total coordination information known as specified in the table. 1.465 m Slope distance Horizontal angle Vertical angle Total coordination I 90⁰ 264.948 m 215° 52' 28' 91° 56' 07' 5150.500 E 2222.640 N R.L 123.565 R.L ?? • Calculate the reduce level of the ground at the base of the shed. Show calculation process. 2.2 m
HI PLEASE HELP CAN YOU HELP ME WRITE AN OBJECTIVE, INTRODUCTION AND CONCLUSION (ATTACHED PHOTO ARE THE DATA AND RESULTS). ITS ABOUT MEASUREMENT OF VERTICAL DISTANCES: DIFFERENTIAL LEVELING
Item 2 Part A What error results on a 20-m sight with a level if the rod reading is 1.7060 m but the top of the 4-m rod is 0.3 m out of plumb? Express your answer to two significant figures and include appropriate units. error = Submit Provide Feedback Value Request Answer Units ?
Surveying with Construction Applications (8th Edition) Problem 6.3. Describe, in point form, how you can use a theodolite or a total station to prolong a straight line XY to a new point Z. (Assume the instrument is set up over point Y and is level.)
Could you find the HI, ELEVATIONS, CORRECTIONS and Adjustments of Elevation values according to the informations were given in the table below? Please write your answers on an A4 paper with your name, school number and signature to show the phases of solving. Afterwards, you can upload it on LMS system as pdf, jpeg, etc. Adj. Setup Station BS HI FS ELEV. CORR. Elev. BM Mil 1,12 2035,23 1 ТР1 0,3 8,55 2 ТР2 0,76 7,05 3 ТРЗ 0,45 9,82 4 ВМ Oak 11,6 9,51 TP4 12,35 1,71 ТР5 11,37 0,63 7 BM Mil 0,19
Part A What error results on a 20-m sight with a level if the rod reading is 1.7060 m but the top of the 4-m rod is 0.3 m out of plumb? Express your answer to two significant figures and include appropriate units. μÃ error = . 12795 Submit mm 59997 Previous Answers Request Answer ? X Incorrect; Try Again; 5 attempts remaining
HI HELP PLEASEE HI PLEASE HELP CAN YOU HELP ME WRITE AN OBJECTIVE, INTRODUCTION AND CONCLUSION (ATTACHED PHOTO ARE THE DATA AND RESULTS). ITS ABOUT MEASUREMENT OF VERTICAL DISTANCES: DIFFERENTIAL LEVELING
GEFS-CE11- FIELDWORK No.4 The next field work is determining vertical distances of selected points on the ground surface through the use of a leveling instrument. For the reason that there is no instrument available at your home, I will provide a data for you to work on. Do the computation by showing the complete solution on paper, fill up the table in the manual, and draw an approximate figure showing the series of observation from BMg to BM10. DIFFERENTIAL LEVELING DATA: From the fieldnotes below, determine the elevation of BM10 and Do the arithmetic Check. STATION B.S H.I. F.S. ELEV REMARKS BM8 1.40m 199.65 m TP1 1.35m 1.55m TP2 1.27m 1.48m ТРз 1.29m 1.48m TP4 0.55m 1.78m BM9 1.40m 1.50m Ramp TP5 1.45m 1.33m TP6 1.48m 1.28m TP7 1.27m 1.36m ТРв 1.50m 1.28m TP9 1.41m 1.11m BM10 1.42m
A-15 m- 33 m Q2) The figure to the right shows a rectangle ABCD, in which A, B, and C are the stations where staff readings were obtained with a level set up at E and D. The observed readings are given in Table. 20 m Staff reading at level location A B C 1.85 0.803 D 2.42 1.361 1.659 48 m If A is a benchmark having elevation of 70 m. Note: the deflection angle in Line of sight (5) is + 0.1146 degree. Level 1. calculate the correct elevations B and C 2. if the height of instrument at E = 1m, and at D= 1m, what is the height difference between D and E
Complete the following set of profile level notes to answer questions [Select] [Select] [ Select] Station BS BM1 2.565 1+100 1+200 TP1 1+300 1+400 1+500 HI FS IFS TP2 1.946 ? 1.946 BM2 ? 33.562 3.741 1.768 2.543 The HI at TP1 is 1.154 0.752 3.051 Elevation (m) 32.756 ? 31.500 30.429 The elevation at station 1+100 is The backsight reading at TP1 is