Obtain the state space representation (equation of state) of the following electrical circuit considering that the inputs are the voltage sources "va" and "vb)" and that the outputs are the voltages measured at the terminals of both capacitors R₁ R₂ R3 11 1/2 U₂
Q: There must be a step missing between step 1 and step 2. The end of step 1 clearly indicated that…
A:
Q: A 3-phase, 10-kVA, 400-V, 50-Hz, Y-connected alternator supplies the rated load at 0.8 p.f. lag. If…
A: In this question We need to determine the voltage regulation Given R= 0.5ohm X= 10 ohm Voltage…
Q: A single phase full converter is connected to a 120 V, 60 Hz supply. It has a RL load having L=6.5…
A: Option D: 60 degrees is the correct answer Solution is given below in step 2
Q: An electrical load operates at 290 Vrms. The load absorbs an average power of 8 kW at a lagging…
A: Given In this we have given the voltage is 290 Vrms , power absorbed is 8kW at a lagging power…
Q: Design a combinational circuit that allows to convert a number entered in excess-3 to gray code. For…
A: According to the question, we need to design a combinational circuit that allows to convert a number…
Q: Prove reciprocity theorem by interchanging the position of 120V source and I
A: The reciprocity theorem state the current in one point due to voltage source is same as after…
Q: I, R₁ X₁ + V₁ Io Ro Il' + X. E₁ 1₂. + E₂ + E3 R₂ X₂ + V₂ R₂ X3 + V3
A: Rearrange the above electrical circuit is,
Q: -f -10x Q3-A-Find the Fourier series components of the signal 10 ث إضافة ملف x (+) = a + Σ an…
A: We need to find out Fourier series for the given signal.
Q: 5. Regenerative braking of a DC motor can not be performed by: a) first quadrant chopper drive b)…
A: it is asked in which drive the regenerative braking of DC motor can not be performed
Q: Question 3 a) Find the spectrum of x(t) = e²t u(1-t) b) Find the inverse Fourier transform of X (w)…
A:
Q: Θ 60 Ω 45 Ω + 24 110V 520Ω {502 50 510 Ω
A: When more than one source is present in the electrical network, the Superposition theorem is used.…
Q: H/// For system shown. Find steady state error RIS) For unit step input. also find Gefficient for…
A:
Q: B9. Regenerative braking of a DC motor can not be performed by: a) first quadrant chopper drive b)…
A: DC motor A DC motor is an electric motor that runs on direct current (DC) electricity. It is…
Q: Find the collector-base junction capacitance (in micro F) for a BJT operating at a de collector…
A: Given data, Zero voltage junction capacitance Cμ0=15 μF Voltage VCB=1.5 V Voltage VOC=0.5 V m=0.4…
Q: a) i) A signal has an r.m.s. value of 8. It is affected by AWGN with a noise standard deviation of…
A: We need to find out signal to noise ratio for given signal .
Q: O Vin w Vout Consider Vo Rout? VAZO Av ? Rin?
A: Since you have asked multiple questions in a single request, we will be answering only the first…
Q: çıkış voltajı eo olacak şekilde yazınız. (write down dynamic differential equation and transfer…
A:
Q: Calculate the p.d. VAB in the next circuit. 100 V 10 Ω 5 Ω 2Ω 15Ω 15 Ω Ο Α Ο Β
A: 13
Q: The fuel-cost functions in S/h for two 800 MW thermal plants are given by C1-400-6P1-0.004(P1 P11,…
A: The incremental cost of power is defined as the rate of change of cost per unit of power. d Cd P=λ
Q: Question 1: Calculate the values of A, B and C for the system shown below, where x(n) and y(n) are…
A: We need to find out the unknown for given system .
Q: Subsystems and elements of the EPS. Description of their functions
A: We need to tell about the EPS and it's subsystem .
Q: Find Y(s) dan y(t) for the following function. dy² dt² + dy = x(t)- + dt 2dx dt and x(t) = e-2t
A: Given data, Function is given as, dy2dt2+dydt=xt+2dxdt and xt=e-2t.
Q: Calculate the cut-off frequency of the following filter V₁N (t) ( IN 3.3ΚΩ 0.5μF VOUT
A: We need to find out the the cut off frequency for given circuit.
Q: Consider a stable CT LTI causal system whose transfer function G(s) is unknown. You are told that,…
A: We need to find out the transfer function for given input and output.
Q: A synchronous generator connected to a 50 Hz infinite bus bar through a transformer and transmission…
A:
Q: If its known that AC Voltage Source Vs = 60V / 50Hz by Using simulation and any Voltage source and…
A: The given circuit is shown below, The AC voltage source is Vs=60 V/50 Hz
Q: QUESTION 4 a) Convert the SR flip-flop in Figure Q4a to behave like JK flip-flop. # R Clock ā pl
A: Since you have asked multiple questions in a single request, we will be answering only the first…
Q: For the system shown below, the receiving end voltage at the load is 33kV. Determine the required…
A: Given data, For transformer 1, Sbase(old)=200 MVAZpu(old)=0.1 p.u.Sbase(new)=100 MVAVbase(old)=275…
Q: a) Develop the state table for JK flip-flop and D flip flop as shown in Figure Q4a. Then, modify the…
A:
Q: 3. Expand the following functions in Fourier series. f(x) = 1 (0 < x < π) (π <x<2π) a. = -1 b. f(x)…
A: A piecewise function is a function that is constructed from bits of various functions across various…
Q: Q 6 please
A:
Q: 1. Find E at (0, 0, 5) m due to Q₁ -0.35 μC at (0, 4, 0) m and Q2 = -0.55 μC at (3, 0, 0) m (see the…
A:
Q: Consider the following circuit, Thevenin resistance Rth is: 1202 72 V Select one: O a. None of these…
A:
Q: 6. In the circuit shown in Figure determine the terminal voltage of the source VS, the power PL…
A: The given circuit is shown below. The given values of circuit parameters are written below. Source…
Q: 6Ω 2A 360 1 A 1 50 1752 34 V 1.50
A: By Applying the source transformation to each of the current source will give the following circuit…
Q: Determine the voltage gain, the center frequency, the bandwidth, and Q for the active bandpass…
A: The given filter circuit is a cascade connection low pass filter and high pass filter. The voltage…
Q: -1 0 Question 2 2 3 4 n 5 -1 0 -1 1 1 2 n 3 -1 a) Find the output signal y[n] for the system shown…
A:
Q: A single-phase power system is shown as the equivalent circuit below. The system has a 480V…
A:
Q: function given as G(s) = k s(st 3) (5+4) 1. Represent the poles of the system in the S plane 2.…
A:
Q: The system below shows a generator supplying a load through a step-up transformer, a transmission…
A:
Q: c) d) Explain the different between sequential circuit and combinational circuit. Identify input…
A: Types of Flip Flop S R Flip Flop JK Flip Flop T Flip Flop D Flip Flop
Q: a) n₂ $₁ $₂ n₁ n, sin (₁) = n₂ sin (₂) b) Pc = sin 0, 7₂ n₁ *** Figure 2.1: Reflection and…
A:
Q: what is the different of Quasi-stationary heating model (Resistivity p is function of specific…
A: Model for quasi-stationary heating: The research on heat transport in this paper is focused on a…
Q: A 10 GHz uniform plane wave is propagating in the positive z direction and is incident from free…
A: Given: In this question, the given details are, A 10 GHz uniform plane wave is propagating in the…
Q: You are designing a pressure measurement system. The nominal pressure to be measured is 30 kPa at a…
A: a) The input range of the MPX53GP pressure sensor is -14.5 to +50 kPa. b) The input span of the…
Q: (a) This diagram shows a cross-section of a conductor arrangement in a "figure of eight" cable. Each…
A: a) Given, Two conductors each carrying a current of I=3 Amp The figure depicts the problem…
Q: The open loop transfer function of the feedback control system is given by G(s) =…
A: G(s) = Ks+3s(s+4)2(s+5)(s+6) We have to find the number of asymptotes and the centroid of…
Q: (a) With aid of suitable diagram, explain the losses and power-flow of an induction motor. (b) A…
A:
Q: Find Vo, using source transformation? 12V + 3ΚΩ O a. None of these Ο b. 12 Ο c 03 O d-3 O e 6 Vo 4ΚΩ…
A: We need to find out the voltage for given circuit.
Q: a- What is the kind of transistors Q1 and Q2 b- Determine which the voltages of (Vi) make the bulb…
A: As per Bartleby guidelines, I am solving the first question. Please post the next question (b)…
Trending now
This is a popular solution!
Step by step
Solved in 3 steps with 3 images
- You are a journeyman electrician working in an industrial plant. Your task is to connect an inductor to a 480-V, 60-Hz line. To determine the proper conductor and fuse size for this installation, you need to know the amount of current the inductor will draw from the line. The nameplate on the inductor indicates that it has an inductance of 0.1 H. An ohmmeter reveals that it has a wire resistance of 10 . How much current should this inductor draw when connected to the line?You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.For the circuit below, determine the current in each branch and the potential difference in the inductor immediately after switch S isclosed. After a long time the switch S is then opened. What are the currents in each branch and the potential difference in the inductor at that moment?
- 1. A 2F capacitor is connected in series with a diode and a 60 resistor. The voltage of the battery is 9V. The forward voltage drop of the diode is 0.7V. Flip to close the switch at t=0. Determine the voltage and current of the capacitor at t=0, t=12s, t=24s, and t=36s. (The following table may help you with this question. Feel free to use this table (or not).) Vc VR I R1 60 H Time=0 Time=12s Time=24s Time=36s1. Find the voltages across the following components (a and b) after 1 second. The Capacitor is initially charged at 10V while the voltage source is 1V. Resistor R is 103 ohm while capacitor C is 1mF. a. Capacitor C b. Resistor R c. What is the best 1st order DE Method applicable to this problem?The magnitude of the voltage applied to the electrodes of a welding machine can be adjusted in the circuit below. In the range of minimum and maximum value that variable value resistor can take What is the time interval that the capacitor will charge from 0 to 8 V?
- 2 The figure is a graph of ... 5 (5 Points) Current Voltage the current across a voltage as a function of the potential difference through it the resistance as a function of the current across a component the current through a component as a function of the voltage across it All three of the above (a), (b), and (c) are true None of the above (a), (b), or (c) is trueUsing the series circuit in Figure 3 consisting of a voltage source V, the resistor R and the fully uncharged capacitor C, how to find the value of the capacitance C considering as known data the time constant of the circuit T and the value of the resistor R? V ww RFor the network shown in figure (3), if the switch is closed for 2usec and then opened for Susec, find mathematical expressions for vi and in of both periods of time and then plot the waveforms of vL and i as a function of time.