PART B-ANALYSIS OF THE RESULTS 1- Using the following graph (with labelled axes) plot the experimental angle of twist versus the torsional moment, or torque T, for the three shafts with L= 300 mm, using dark crosses (+) to indicate the actual data points; label each set of data points according to its shaft diameter, "D =- - - mm".

PART B-ANALYSIS OF THE RESULTS 1- Using the following graph (with labelled axes) plot the experimental angle of twist versus the torsional moment, or torque T, for the three shafts with L= 300 mm, using dark crosses (+) to indicate the actual data points; label each set of data points according to its shaft diameter, "D =- - - mm".

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In-1' 16+29 CHAPTER ENGINEERS MECHANICS STATICS り」 arc ( 24 X(x Sample Problem 6.4.2 JQ) aX9 142 i JA V4 TuS 31 An 800 N-m couple is applied to the flywheel as shown. The coefficient of belt friction is 0.20. The minimum force P required to prevent rotation of the flywheel is applied. 800 N.m dre 2.R 1. Which Tension is larger, TA or TB? Explain 2. What is the angle of contact in radians? 60 3. What is the value of the ratio TA/TB? A B X*ッー Sin=d 6+ミ 2(I+(T Tarc (2) 4)e Eら、1.2 J =3.
Q.3 In a bushmandrel system, a bush was turned on a mandrel. The mandrel diameter in millimeter is 400.00 -0.05 and bore diameter of bush is 40+0.06 The -0.010 maximum eccentricity of the bush in mm will be A 0.025 0.045 C 0.055 D 0.065
Turning moment 1mm = 60NM: crank angle, 1 mm = 1°. The turning moment shows the maximum energy that needs to be stored by the flywheel in unit area is 2850 m?. The flywheel rotates at an average speed of 220 rpm with a total speed change of 2.5%. If the mass of the flywheel is 500 kg, find the appropriate dimensions (inner diameter, outer diameter and thickness) of the flywheel. Given that inner diameter of the flywheel is 0.9 outer diameter and the density is 7.2 Mg/m3. Reply.
2000 1250 (3) G F Load, F 750 31.0° D. 4 2500 1250 750 C 500 RAX A 33.7 RBX Dimensions in millimeters RA TRAY Rp RBy 42.5° 33.7 Reaction forces at supports A and B
Assuming there is no axial thrust, find the reactions @ A & C. Y Note: Force actlig on gear B is parallel to z-axis. Force acting on year D is parallel to y-ax's. 50 70015 3010 25 in 86916 201 100
Problem 2. A 300-mm diameter solid disk is to be used as a flywheel in a machine to reduce speed fluctuations. If the disk material has yield strength S Y =720 MPa, density p=7000 kg/m^ 3 . and Poisson's ratio J = 0.2 ^ c , find the maximum allowable rotational speed (in rpm) for a safety factor of 1. a) Solve using the MSST. b) Solve assuming that the disk is mad of cast iron having Sut = 207MPa , Fuc = 780MPa, p = 7000 kg/m³, and Poisson's ratio v r = 0.26 , Use Coulomb-Mohr theory.
Find the diameter of the shaft (based on torsional stiffness) for which the angle of twist is not to exceed 1 degree in 20 diameters. The shaft transmits 5 hp and rotates 100 rpm. The modulus of elasticity (shear) is 12,000,000 psi and the modulus of elasticity (tension) is 30,000,000 psi. a. 7.8048 inches. c. 3.6286 inches b. 1.4524 inches d. 5.2462 inches
3. A cylindrical rod is composed of two pieces of different diameters. Both pieces are made of the same material. Torques are applied at points B and D, with the directions shown below. The magnitudes of the torques are Tg = 4000 in-lb, Tp = 3000 in-lb. JAC = 4 in L = 10 in. JcD = 2 in GẠC = GCD = G = 10 × 10° psi Determine the twist of point B, Ør, and the twist of point D, øp, relative to the wall at A. Note definition for + and – twist, shown to the right. Ans: = -0.25x10³ radians, øp = 2.0×10³ radians A D Tp IB Fixed to wall
b) the following data is given for the piston of a four-stroke diesel engine: Cylinder bore 300 min Force on piston due to maximum gas pressure = 424 KN Bearing pressure at small end of connecting rod = 15 MPa Length of piston pin in bush of small end = 0.45D Ratio of inner to outer diameter of piston pin = 0.6 Mean diameter of piston boss = 1.4 x outer diameter of piston pin Allowable bending stress for piston pin = 84 N/mm2 %3D Calculate i. Outer diameter and inner diameter of the piston pin ii. Mean diameter of the piston boss; iii. The maximum gas pressures iv. check the design for bending stresses.
What is the minimum diameter in mm of a solid steel shaft that will not twist through more than 3° in 6 meter length, when subjected to a torque of 14 kN m. Use G of 83 Gpa. 1180 118 0.0118 O 0.118
Turning moment 1mm = 60 Nm: crank angle, 1 mm = 1° . The turning moment shows the maximum energy that needs to be stored by the flywheel in the unit area is 2850 m² . The flywheel rotates at an average speed of 220 rpm with a total speed change of 2.5%. If the mass of the flywheel is 500 kg, find the appropriate dimensions (inner diameter, outer diameter and thickness) of the flywheel. Given that inner diameter of the flywheel is 0.9 outer diameter and the density is 7.2 Mg/m³ .
Choose correct answer: The outer diameter of the shaft is 10 cm & the diameter ratio is 1.25. Find the polar modulus of the shaft _______________cm3. 115.92 1.159 1159.2 11.59