Problem 2: The stresses shown act at a point on the free surface off a stressed body. a) Determine the principal stresses and the maximum in-plane shear stress acting at the point b) Show these stresses in an appropriate sketch. c) Determine the normal stresses on and ot and the shear stress Tnt that act on the rotated stress element. 53 MPa 16 MPa 47 MPa 35⁰

Problem 2: The stresses shown act at a point on the free surface off a stressed body. a) Determine the principal stresses and the maximum in-plane shear stress acting at the point b) Show these stresses in an appropriate sketch. c) Determine the normal stresses on and ot and the shear stress Tnt that act on the rotated stress element. 53 MPa 16 MPa 47 MPa 35⁰

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The normal and shear stresses acting on element A are 6,650 psi, 17,600 psi, and 2,700 psi (see part (b) of the figure below). (Consider only the in-plane stresses - the stresses in the xy-plane). 117,600 psi B A 6,650 psi A Cross Side |2,700 psi Section View (a) (b) Determine the maximum shear stresses (in psi), associated normal stresses (in psi), and angles of the principle planes (in degrees counterclockwise from the +x-axis). (For maximum shear stress, enter the magnitude. For normal stresses, use the sign convention for stresses acting on inclined sections.) max = psi psi 02 psi %3D ° counterclockwise from the +x-axis p1 p2 ° counterclockwise from the +x-axis
1) Figure 1 shows an element with stresses. Angle 1 Oy Tyx Txy Tyx Figure 1 Point B- x-direction stress 60MPA(tension), y-direction stress 40MPA(compression), positive shear stress 30MPA a) From basic priciples determine the stresses on the plane of the indicated angle 1. (20°), Show al calculations. Draw the orientation of the stress block for this scenario. b) Repeat question (a) using a Mohr circle.
(Problems No. 1 - 3) The state plane stress at a point is represented by the stress element below. Determine the stresses acting on an element oriented 30 degree counterclockwise respect to the original element. Calculate the shearing stress at the xy-face 60 MPa 20 MPa 90 MPa O a. -55 MPa O b. 65 MPa 55 MPa O d. -65 MPa
element in each case. Question 3. Determine the principal stresses, the maximum in plane shear stress, and average normal stress. Specify the orientation of the Question 4. The state of stress at a point in a member is shown on the plane AB. element. Determine the stress components acting on the inclined 200 MPa 500 MPa 40 MP1 350 MPa 65 MPa
1) Figure 1 shows an element with stresses. Angle 1 Oy Tyx Ox Txy Tyx Figure 1 Point Ax-direction stress 60MPA(compression), y-direction stress 40MPA(tension), negative shear stress 30MPA a) From basic priciples determine the stresses on the plane of the indicated angle 1-30°, Show al calculations. Draw the orientation of the stress block for this scenario. b) Repeat question (a) using a Mohr circle.
The tensile member shown, 60mm x 80mm in cross-section is subjected to a load of 250kN. The plane AA’ makes an angle of 15o with the x-axis. What is the tensile stress of section AA’? Determine the shear stress on plane AA’ At what angle of plane AA’ is the shear maximum.
1. Determine the maximum tensile and compressive bending stresses in the beam shown. 6 kN A B C 120 1.0 m 1.2 m 2 kN -| 4090→ 40 |- Dimensions in mm 2. Find the lightest S-shape for the beam shown if the working stress in bending is 120 MPa. What is the maximum bending stress in the beam selected? 40 kN/m 4 m - 2.4 m 3. For the beam shown in the figure, find the shear stress at a point 30 mm above the bottom of the beam at section C. 50 mm | 14 kN E1.5 m – 3 m 100 mm I = 19.3 × 106 mmª B C A NA 62.5 mm 50 mm 2 m 100 mm 4. The simply supported wood beam, fabricated by gluing together four wooden boards, carries the three concentrated forces. The working bending and shear stresses for the wood are 1000 psi and 600 psi, respectively. Determine the largest allowable value of the force P. P 0.5 in. → -8 in.→+ 0.5 in. P 2 in. 2 ft -4 ft-+ 4 ft→ 2 ft 6 in. $2 in. SAP
A cube (E - 20OGPA) is experiencing stress from all directions. Along the x-direction, there is a compressive stress of 50MPA. Along the y-direction, there is a tensile stress of 80MPA. Along the z-direction, there is a tensile stress of 100MPA. Solve the strain along the z-axis if the Poisson's Ratio is 0.3. O 0.000520 O 0.000455 O 0.000416 0.000325
Detemine the principal stress acting at point B, which is located just on the web, below the horizontal segment on the cross section Show the results on a properly oriented element located at this point. Although it is not very accurate, use the shear formula to calculate the shear stress. -AO mm- 300 mm 150 mm 12 mm 130 mim 15 mm 6 kN
What is Mohr's circle of stress? At a point in an elastic material, a direct tensile stress of 60 kN/mm² and a direct compressive stress of 40 kN/mm² are applied on planes at right angles to each other. If the maximum principal stresses are limited to 75 N/mm² (tensile). Find the shear stress that may be allowed on the planes. Also determine the minimum principal stress and the maximum shear stress. 10001
Q-5: For the element with stresses as shown below, find: a. The magnitudes and directions of major and minor principal stresses b. The shear and normal stresses acting on a horizontal plane as shown below 8kPa 2kPa 75° 75° экра TH Jon OH 4kPa 30° Horizontal plane
PROBLEM 7.63 For the state of stress shown it is known that the normal and shearing stresses are directed as shown and that o, =98 MPa, ơ, = 63 MPa, and omin = 35 MPa. . Determine (a) the orientation of the principal planes, (b) the principal stress Omaxs (c) the maximum in-plane shearing stress.