Problem 208 A steel tire, 10 mm thick, 80 mm wide, and 1500.0 mm inside diameter, is heated and shrunk onto a steel wheel 1500.5 mm in diameter. If the coefficient of static friction is 0.30, what torque is required to twist the tire relative to the wheel? Neglect the deformation of the wheel. Use E = 200 GPa.

Problem 208 A steel tire, 10 mm thick, 80 mm wide, and 1500.0 mm inside diameter, is heated and shrunk onto a steel wheel 1500.5 mm in diameter. If the coefficient of static friction is 0.30, what torque is required to twist the tire relative to the wheel? Neglect the deformation of the wheel. Use E = 200 GPa.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.57P: The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a...

See similar textbooks

Similar questions

The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a mean radius of 75 mm. The static and kinetic coefficients of friction between the gear and the screw are 0.12 and 0.06, respectively. The input torque applied to the screw is C0=10Nm. Assuming constant speed operation, determine the output torque C1 acting on the gear.
A ladder of length 2L and mass M is positioned on level ground leaning against a wall such that the angle between the ladder and the horizontal is @. The coefficient of static friction between the ladder and the wall and between the ladder and the ground is jistatic = 0.66. The centre of mass of the ladder is halfway along it. For the ladder to be in mechanical equilibrium: Consider torques about the centre of the ladder. In which direction (into or out of the page) does the torque due to each of the 5 forces force act?Write down an equation for the sum of the torques about the centre or mass of the ladder and then use your equation for the torques to derive an expression for tan o in terms of the magnitudes of the forces acting
The effective pressure on a 400 mm diameter piston is 1.1 MN/m² when the crank is 32° beyond top dead centre. The stroke of the engine is 900 mm, the connecting rod is 1500 mm in length and the coefficient of friction for the lubricated crosshead guide is 0.025. Calculate EACH of the following: (a) the magnitude of the instantaneous torque; (b) the magnitude of the instantaneous force to overcome guide friction.
A car engine has its rated output of 120 kW. The maxdmum torque developed is 110 Nm, The clutch used is of single plate type having two active surfaces. Axia! pressure is not to exceed 0.85 bar. External diamater of friction plate is 1.25 times the internal diameter. Determine the dimensions of friction plate and axial force exerted by the spring. Assume uniform wear and coefficient of friction to be 0.3.
The hand brake of Fig. is used to control the rotation of a drum. The coefficient of friction between the belt and the drum is , = 0.15, and the weight of the handle may be neglected. If a counterclockwise torque of 5 ft - Ib is applied to the drum Repeat the problem for a clockwise torque of 5 ft · Ib. What happens to the system at a 4.6 in.? What does the solution mean for a> 4.6 in.? M= 5 lb-ft -12 in. 12 in
Steel frame with thickness of 10mm, width 80mm and inner diameter of 1500.0mm being heated and shrinkable on steel wheel diameter 1500.5mm. If the coefficient of static friction is 0.30, what is the torque required to roll the tire with respect to the wheel? Neglecting the deformation of the wheel. Use E = 200 GPa.
2. A square threaded screw of mean diameter 25 mm and pitch of thread 6 mm is utilised to lift a weight of 10 kN by a horizontal force applied at the circumference of the screw. Find the magnitude of the [Ans. 966 N] force if the coefficient of friction between the nut and screw is 0.02. A bolt with a squore threaded screw has mean diameter of 25 mm and a nitch of 23 mm It carries an
Refer to Fig 33. The homogenous body A weighs 120 lb. The coefficients of frictions are 0.30 between A and the plane and 2/pi between the rope and the drum. What value of W will cause motion of A to impend? Give solution. (Ans. W= 81.5 lb)
A cone clutch has cone elements at an angle of 12o. The clutch transmit 25 HP at a speed of 1200 rpm. The mean diameter of the conical friction section is 16 in and the coefficient of friction is 0.35. Find the axial force needed to engage the clutch.
A block brake with a torque of 250 N-m. Its drum rotates at 100 rpm. The length of the block (1) is twice its width (w). Assume, the coefficient of friction P is 0.35. Calculate: (1) the applied load (P) and the hinge-pin reaction (Rx ana Ry) for clockwise rotation of the drum; (2) the applied load and hinge-pin reaction for anticlockwise rotation of the drum; (3) the rate of heat generated during the braking action. (4) The dimensions of the block, if the intensity of pressure between the block and brake drum is 1 MPa. (5) Check whether the brake is self-locking.
3 A flat collar bearing has an external diameter which is 1.6 times the intenal diameter. The coefficient of friction is 0.05 and the maximum bearing pressure is 270 kN/cm^2. The axial load is 20 kN and power absorbed due to friction is 30 kW when the shaft rotates at 750 rpm. If the bearing becomes worm so that the bearing presuure is inversly proportional to the radius, the total axial force and the speed of rotation remaining the same as before, calculate (a) the bearing radii (b) the wear constant (c) the number of collars required
An overhang shaft carry a 900mm diameter pulley, whose center is 250mm from the center of nearest bearing. The weight of the pulley is 600N and the angle of lap is 180°.The pulley is driven by motor horizontally to right it, if the permissible tension in the belt is 2650N and the coefficient of friction between the belt and the pulley surface is 0.3, estimate the diameter of the shaft. Note, Neglect centrifugal tension and assume permissible tensile and shear stresses in the shaft as 84MPA and 68MPa respectively.