Select the best mining method to mine a 35 meters thick and 750 meters long mineral deposit, located 900 meters below the surface and dipping at 65 degrees. The ore value is moderate to high and the host rock strength is high. The estimated dilution is about 18 % and the required production rate is approximately 8,500 tons per day. None of these answers Block caving Room and pillar Open stoping Sublevel caving Shrinkage stoping Cut and fill

Select the best mining method to mine a 35 meters thick and 750 meters long mineral deposit, located 900 meters below the surface and dipping at 65 degrees. The ore value is moderate to high and the host rock strength is high. The estimated dilution is about 18 % and the required production rate is approximately 8,500 tons per day. None of these answers Block caving Room and pillar Open stoping Sublevel caving Shrinkage stoping Cut and fill

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

How are pacer mining, hydraulic mining, and hard-rock mining different?
A limestone mine has the following equipment at its primary production face: Excavator: a 15 yd3 (11.5 m3) front-end loader with 40 sec cycle time Trucks: five 100 ton (90 tonne) trucks Material: average blasted rock with medium-hard digging conditions Working conditions: average Haulage cycle time: 20.0 min (a) What is the sustained production rate of the system in tons/hr, assuming 60 min of production per hour'? (b) Which equipment (loader or trucks) governs? (c) What improvements would you recommend to increase mine production without changing equipment?
A new underground Lead-Zinc-Silver mine is planned to start at a depth of 1200 m below the surface level with an annual ore production of 2 million tons. After performing insitu testing, it was found that the proposed mine site is having very high horizontal stresses compared to the vertical stresses. Based on the given situation, what stability and ground control challenges will be there in your opinion and how you will manage them in a most effective manner without compromising with the safety and stability
the formula should be GL mines something
6.7 How can we identify faults in the fields? 6 8 WVhat ore the nmein
Define the Purkaystha and Char reduction factor method ?
2.2/Multiple choices. Select 10 only: - (2 1. 1. In thi land Paleta anania r 2. WHICH.. ****** Q lange Ca J www.por 7. Fissile or foliated metamorphic rocks are mono mineral or multi minerals? 8. Which one has more water contain, clay or mari? 9. Which one has not water molecule, gypsum or anhydrite? 10. Concentrated closed circles contours with highest value in the center, is it basin or dome? 11. Paramagnetic minerals are attracted to magnet or not?
The owner of the quarry signs a contract to sell his stone on the following basis The purchaser is to remove the stone from a certain portion of the pit according to a fixed schedule a volume, price , and time. The contract is run 18 years as follows. Eight years excavating a total of 20, 000 m per year at 10 P per meter, the remaining ten years, excavating a total of 59, 000 m per year at 15 per meter. On the basis of equal year end payments during each period by the purchaser, what is the present worth of the pit to the owner on the basis of 15% interest?
Consolidation test results are provided below, (Hint: C, or C = Ae / log(of/ai') ): 1.2 1.1 1- 0.9 Void ratio 0.8 0.7 0.6 0.5 0.4 1 10 100 1000 Vertical stress (kPa) (log scale) In some of the results an interval is provided. It ccan be possible to get a result between the given values Use the plot and find pre-consolidation pressure (past maximum vertical effective stress) pe' according to Casagrande's method. pe'= .kPa Seç. Find C, Seç. Find C.: Seç. If the tested soil sample is taken at a depth of 5m (ysat=18kN/m) where the groundwater table is located at the surface what is the Over Consolidation Ratio(OCR) (OCR= pclo vo) Seç. Initial height of the specimen is 22mm. What is the final height of the specimen when effective vertical stress is 650kPa? Hint: Use void ratio. Seç. (Result is in mm) What is the consolidation settlement of 2m thick clay layer if initial effective stress is 20kPa and final effective stress is 400kPa. Hint: Poc= Seç. [Ho/(1+einit)]x[C,log(p'/o'init) +…
If on-site slump test fails, should engineers allow the contractors to continue the concreting works?
Write three assumptions ,Please do not copy the solution from other site it will be downvoted for sure.
You wish to perform a Statnamic test on a 35 m long 0.5 m diameter concrete drilled shaft. How long must the loading pulse be in order to use the unloading point method to analyze the test?