The force P is applied on the top of the solid cylindrical body which rests on a circular cap as shown below. Determine the smallest dimensions di, ds, and t required to support the load P. Use the table given below and your student ID to obtain the values of the force P and the allowable stresses for all the materials used in the problem (ie., Pand the allowable stresses are given). 30 mm allowable allowable shear allowable tensile stress (kPa) Student bearing stress (kPa) P(N) ID stress (kPa) 1000 175 300 155

The force P is applied on the top of the solid cylindrical body which rests on a circular cap as shown below. Determine the smallest dimensions di, ds, and t required to support the load P. Use the table given below and your student ID to obtain the values of the force P and the allowable stresses for all the materials used in the problem (ie., Pand the allowable stresses are given). 30 mm allowable allowable shear allowable tensile stress (kPa) Student bearing stress (kPa) P(N) ID stress (kPa) 1000 175 300 155

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two vertical steel rods support the rigid bar as shown. Initially, the rods are stress-free. Given the data below, determine the stress of rods A and B after the 20 kN load is applied. Neglect the weight of the bar and use E = 200 GPa for steel. L= 3 m D = 3.5 mm A. Stress of rod A (MPa) B B. Stress of rod B (MPa) C. At what temperature AT change would the stresses for both rods be equal? Use a = 11.7 L= 4 m x 10-6 mm/mmC° (C°) D = 5 mm 4m 2m 2m 20 kN
In this figure is a strut and a cable which was used to lift a body, if the strut and a cable has a stress equivalent to your SN and MN in kips respectively, determine the maximum weight of that body. Neglect the weight of wood and cable. Note: Round off your answer in two decimal places. ... Cable (A = 0.5 in 2) 9 ft C B 12 ft Weight A Wood Strut ( A 16 in 2)
Solve for the indentation diameter if the BHN of the material is 70 and a 500 kg of load is applied? Use indenter diameter 10mm.
Calcuate Torsion and Bending From Point A to Point B and Point A to Point C. Draw a FBD from point A to point B and another for point A to C indicating what stresses are been calculate. Use the stress tensor and stress cube to Indicate what forces are acting at point A. Force apply at point B is 70lb Distacen from Point A to B is 12 in or 1 feet long Distacen from Point A to C is 3 in Handle diameter 0.625 in
Calcuate Torsion From Point A to Point C and Bending from Point A to Point B and from Point A to Point C. Draw a FBD from point A to point B and another for point A to C indicating what stresses are been calculate. Use the stress tensor and stress cube to Indicate what forces are acting at point A. Force apply at point B is 70lb Distacen from Point A to B is 12 in or 1 feet long Distacen from Point A to C is 3 in Handle diameter 0.625 in
The armor shown supports loads of 3 KN. The horizontal elements are 713cm long each. Determine the axial force on element FE; Use the section method to determine the axial force in the FE element and check your result with the nodal or joint method. INFO: Y= 100 cm
The bolt shown on the picture is subjected to total tensile force of 90 kN. Determine the tensile stress at the body of the bolt and tensile stress at root of bolt. Find also the compressive stress at the head as the bolt bears on the surface to resist the tensile load.
Rod of diameter 20 mm is loaded with 5kN tension force. What is the magnitude of stress in the rod?
A 2.4 diameter steel molding is lifted by 4 steel cables as shown. The mold weighs 3 kN/m. (a) what is the required diameter of wire that will not exceed the allowable stress of 120 MPa. and (b) if the wire diameter increase by 20%, find the vertical displacement of the molding. 24m
As shown, three steel wires, each 28 mm2 in area, are used to lift a mass M. Their unstretched lengths are 19.99 m, 19.98 m, and 20 m. If M= 1,182 kg. what stress exists in the MIDDLE wire? Use E=215 Gpa. Answer must be in MPa.
Consider a steel cube with side length L and each of its faces normal to the orthogonal axes x, y, and z as shown below. If the cube is subjected to a constant tensile force T along the x-axis and the faces along the y- and z- axes are left free and unsupported, which of the following best describes what is expected to happen? Z Select one: O A. The cube will expand along the x-axis and compress along the y- and z-axes. B. The cube will expand along the x- and y-axes and will not deform along the z-axis. O C. The cube will expand along the x-axis and will not deform along the y- and z-axes. O D. The cube will compress along the x-axis and expand along the y- and z-axes.
Figure 4: Determine the bar force at FN (Answer in whole number, indicate the answer in kN. just input the value, do this for all the questions on Figure 4) Note: if the member is in compression, write a negative symbol before it, ex: 12kn in compression is answer:-12