The Operational Amplifier in the circuit shown has a slew-rate of 8 V/us. If Vim 0.1 V, then the Maximum allowed frequency non distorted in the circuit FMAX and the maximum gain allowed if FMAX = 2.5 MHz GMAX is: %3D %3D Vin 20 k Ohm 250 k Ohm Vo a. FMAX = 1.019 MHz and GMAX = 5.09 b. FMAX = 2.035 MHz and GMAX = 8.12

The Operational Amplifier in the circuit shown has a slew-rate of 8 V/us. If Vim 0.1 V, then the Maximum allowed frequency non distorted in the circuit FMAX and the maximum gain allowed if FMAX = 2.5 MHz GMAX is: %3D %3D Vin 20 k Ohm 250 k Ohm Vo a. FMAX = 1.019 MHz and GMAX = 5.09 b. FMAX = 2.035 MHz and GMAX = 8.12

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

If ADM = 3500 and ACM = 0.35, the CMRR is ..........
A fixed bias n-channel JFET with Vdd= 12V, Rd= 1.2k ohms. Idss=12mA and Vp=-4V. Determine Vs. a.0 V b.None of these c.4.35V d.6.7V
Sketch the voltage signal v=3cos(5t -20°). Also, determine the peak value, peak-to-peak value, frequency and phase
The circuit is shown below, Vin is the sinusoidal waveform with magnitude 5V and frequency is 100 Hz, R = 1 k, C = 1 uE, the chip is supplied by + 12 V source. a) What is the waveform of Yout? b) Calculate the magnitude of Vo c) If Vin is triangle waveform, what is the output waveform? -Vout , if Vin is triangle waveform with magnitude of 5 V (peak-to-peak value is 10 V) and frequency is 10 kHz, calculate waveform of you and the magnitude of I/?
looking for overall voltage gain
DC to AC 1) Determine the efficiency of the following DC to AC converter (i.e. how much of the energy is in the Ist harmonic?). (on for 10ms (+20V), off for 20ms, on for 10ms (-20V), off for 20ms, repeat) +20V 20ms 20ms 10ms ov 10ms -20V 1) Determine the efficiency of the following DC to AC converter (i.e. how much of the energy is in the Ist harmonic?). +2-V -20V 10ms 20ms Oms 30ms 40ms
Assume VRE 0.7 V and B-50 for the transistor in the circuit shown in the figure. For VCE = 2 V, the value of Rg is RB m B +12 V www Rc- 5 k C E VCE
The condition for small signal analysis is VS must be less than 10mV vce vbe VCC O000
In the forllowing circuit, determine the value of the minimum base current required for saturation given that: Vcc = 12 V, VLED = 1.5 V, VCE(sat) 0.5 V , R. = 200 2, B,c = 50 +Vcc Ic Rc VLED ON ON RB Vin VCE 1s OFF Select one: a. 0.5 mA b. 4 mA C. 6 mA d. 1 mA
iv) dc collector to emitter base voltage, VEca v) dc base voltage, VB vi) dc collector voltage, Vc vii) dc emitter voltage, VE and viii) dc base collector voltage, Vsc. ix) ac and dc loadline by using appropriate sketches x) maximum output swing, Vo max. Given : VEB = 0.7V and ß = 100. 12 V 82k 3k3 C. o Vo Vi o H 1k0 39k CE Figure Q3b
Consider the circuit of Figure 1, with a periodic square signal voltage source at a frequency f = 500 [Hz], consider R = 1600 [22]. Solve the circuit and plot on graph paper (minimum 10 values between 0 and 2 milliseconds) the total current response, taking into account the source Vin = 24 [Vp]. Note: identify in the graph maximum and minimum points of the total current response. Vin CH1 L m 160 mH, 4 Q CH2 REF Figure 1. Series RL circuit. Note: to do by differential equations and not to use laplace
Compute for Zin and Zout. Voltage Gain and Current Gain.