The state of plane stress at a point on the surface of the airplane fuselage is represented by the stress element shown in the figure. Using Mohr's Circle, determine a) the principal stresses and the maximum in-plane shear stress specifying the orientation of the element in each case. b) The equivalent state of stress at the point on the element that is oriented {a} clockwise from this position Draw all the corresponding stress elements. Given x = {x} MPa; y = {y} MPa and xy = {xy} MPa

The state of plane stress at a point on the surface of the airplane fuselage is represented by the stress element shown in the figure. Using Mohr's Circle, determine a) the principal stresses and the maximum in-plane shear stress specifying the orientation of the element in each case. b) The equivalent state of stress at the point on the element that is oriented {a} clockwise from this position Draw all the corresponding stress elements. Given x = {x} MPa; y = {y} MPa and xy = {xy} MPa

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.4.21P: -18 through 7.4-25 An clement in plane stress is subjected to stresses a,, ay., and axy. (see...

See similar textbooks

Similar questions

-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
-18 through 7.4-25 An clement in plane stress is subjected to stresses a,, ay., and axy. (see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
.4-2 An element in uniaxial stress is subjected to tensile stresses sx= 57 MPa. as shown in the figure. Using Mohr’s circle, determine the following. (a) The stresses acting on an clement oriented at an angle 0 = 33° from the x axis (minus means clockwise). (b) The maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
-18 through 7.4-25 An clement in plane stress is subjected to stresses sx,,sy., andtxy(see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with t = 1400 psi and trv = —900 psi, as shown in the figure part a. The figure part b shows an inclined plane aa cut through the same point in the material but oriented at an angle ft Determine the value of the angle 6 between zero and 90° such that no normal stress acts on plane aa. Sketch a stress clement having plane aa as one of its sides and show all stresses acting on the clement
An element in plane stress on the fuselage of an airplane (figure part a) is subjected to compressive stresses with a magnitude of 42 MPa in the horizontal direction and tensile stresses with a magnitude of 9.5 MPa in the vertical direction (sec figure part b). Also, shear stresses with a magnitude of 15.5 MPa act in the directions shown. Determine the stresses acting on an element oriented at a clockwise angle of 40g from the horizontal. Show these stresses on a sketch of an element oriented at this angle.
-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
Solve the preceding problem for an element in plane stress on the bottom surface of a fuel tanker (figure part a); stresses are sx= 105 MPa, sy. = 75 MPa, and ??xy= 25 MPa. Determine the stresses acting on an element oriented at an angle ?? = 40° from the x axis, where the angle is positive when counterclockwise. Show these stresses on a sketch of an element oriented at the angle ??.
During a test of an airplane wing, the strain gage readings from a 45° rosette (see figure) are as follows: gage A, 520 × l0-6; gage B. 360 × l0-6; and gage C,-80 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.
The stresses acting on element A in the web of a train rail are found to be 'X (MPa)' tension in the horizontal x-direction and 'Y (MPa)' compression in the vertical y-direction. Also, shear stresses of magnitude 'S (MPa)' act in the directions shown in the figure. Draw Mohr's circle for the state of stress. Determine the stresses (Ox', Oy' and Txy') acting on an element oriented at an angle 'D' from the horizontal Show these stresses on a sketch of an element oriented at this angle X=45MPA,Y=150MPA,S=52MPA,D=-40 Degree
2- The state of stresses at a point are defined as follows. Find the normal and shear stress vector components (O₂. ) on a plane tangent to a cylinder of diameter D and coaxial with x-axis (Z-axis) at point (B.y.B). Also, determine the octahedral shear stress. Stu. Nom. D B Y 30 45 60 5.0 2.0 1.5 Ju = 45 20 50 MPa 60 50 10