Fundamentals Of Engineering Thermodynamics
9th Edition
ISBN: 9781119391388
Author: MORAN, Michael J., SHAPIRO, Howard N., Boettner, Daisie D., Bailey, Margaret B.
Publisher: Wiley,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 1, Problem 1.28P
To determine
Reading of bourdon gauge and its type
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The Louisiana Superdome has an interior volume of 125 million ft3, covered by a 440,000 ft² roof. On a
particular day, the interior air pressure gave a manometer reading of 19 inches mercury (pHg = 13.6 g/cm³).
Local atmospheric pressure is 102 kPa.
1.
kg
Calculate the mass of the air inside, assuming an average temperature of 20 °C.
2.
kN
Calculate the net force applied to the roof by the interior/exterior air (do not
account for the weight of the roof). Assume the roof is flat.
Air at pressure 173.9 kPa flows through a pipe. The actual volume flow rate of air through the pipe is
measured to be 6.85 m3/s. The standard volume flow rate of this air flow is 2.71 m/s. Calculate the air
density in units of kg/m3. Hint: The ideal gas equation is useful for air.
An open tube mercury manometer is used to measure the pressure in an
oxygen tank. When the atmospheric pressure is 1040 mbar, what is the
absolute pressure (in Pascal) in the tank if the height of the mercury in the
open tube is 28 cm higher? (density of mercury = 13.6 X 10° kg/m³) *
O 1.41 X10 pa
O 2.34 X105 pa
O 1.82 X105 pa
O 2.12 X105 pa
Chapter 1 Solutions
Fundamentals Of Engineering Thermodynamics
Ch. 1 - Prob. 1.2ECh. 1 - Prob. 1.3ECh. 1 - Prob. 1.4ECh. 1 - Prob. 1.5ECh. 1 - Prob. 1.6ECh. 1 - Prob. 1.7ECh. 1 - Prob. 1.8ECh. 1 - Prob. 1.9ECh. 1 - Prob. 1.10ECh. 1 - Prob. 1.11E
Ch. 1 - Prob. 1.12ECh. 1 - Prob. 1.13ECh. 1 - Prob. 1.14ECh. 1 - Prob. 1.1CUCh. 1 - Prob. 1.2CUCh. 1 - Prob. 1.3CUCh. 1 - Prob. 1.4CUCh. 1 - Prob. 1.5CUCh. 1 - Prob. 1.6CUCh. 1 - Prob. 1.7CUCh. 1 - Prob. 1.8CUCh. 1 - Prob. 1.9CUCh. 1 - Prob. 1.10CUCh. 1 - Prob. 1.11CUCh. 1 - Prob. 1.12CUCh. 1 - Prob. 1.13CUCh. 1 - Prob. 1.14CUCh. 1 - Prob. 1.15CUCh. 1 - Prob. 1.16CUCh. 1 - Prob. 1.17CUCh. 1 - Prob. 1.18CUCh. 1 - Prob. 1.19CUCh. 1 - Prob. 1.20CUCh. 1 - Prob. 1.21CUCh. 1 - Prob. 1.22CUCh. 1 - Prob. 1.23CUCh. 1 - Prob. 1.24CUCh. 1 - Prob. 1.25CUCh. 1 - Prob. 1.26CUCh. 1 - Prob. 1.27CUCh. 1 - Prob. 1.28CUCh. 1 - Prob. 1.29CUCh. 1 - Prob. 1.30CUCh. 1 - Prob. 1.31CUCh. 1 - Prob. 1.32CUCh. 1 - Prob. 1.33CUCh. 1 - Prob. 1.34CUCh. 1 - Prob. 1.35CUCh. 1 - Prob. 1.36CUCh. 1 - Prob. 1.37CUCh. 1 - Prob. 1.38CUCh. 1 - Prob. 1.39CUCh. 1 - Prob. 1.40CUCh. 1 - Prob. 1.41CUCh. 1 - Prob. 1.42CUCh. 1 - Prob. 1.43CUCh. 1 - Prob. 1.44CUCh. 1 - Prob. 1.45CUCh. 1 - Prob. 1.46CUCh. 1 - Prob. 1.47CUCh. 1 - Prob. 1.48CUCh. 1 - Prob. 1.49CUCh. 1 - Prob. 1.50CUCh. 1 - Prob. 1.51CUCh. 1 - Prob. 1.52CUCh. 1 - Prob. 1.53CUCh. 1 - Prob. 1.54CUCh. 1 - Prob. 1.55CUCh. 1 - Prob. 1.56CUCh. 1 - Prob. 1.57CUCh. 1 - Prob. 1.58CUCh. 1 - Prob. 1.4PCh. 1 - Prob. 1.5PCh. 1 - Prob. 1.6PCh. 1 - Prob. 1.7PCh. 1 - Prob. 1.8PCh. 1 - Prob. 1.9PCh. 1 - Prob. 1.10PCh. 1 - Prob. 1.11PCh. 1 - Prob. 1.12PCh. 1 - Prob. 1.13PCh. 1 - Prob. 1.14PCh. 1 - Prob. 1.16PCh. 1 - Prob. 1.17PCh. 1 - Prob. 1.18PCh. 1 - Prob. 1.19PCh. 1 - Prob. 1.20PCh. 1 - Prob. 1.21PCh. 1 - Prob. 1.22PCh. 1 - Prob. 1.23PCh. 1 - Prob. 1.24PCh. 1 - Prob. 1.25PCh. 1 - Prob. 1.26PCh. 1 - Prob. 1.27PCh. 1 - Prob. 1.28PCh. 1 - Prob. 1.29PCh. 1 - Prob. 1.30PCh. 1 - Prob. 1.31PCh. 1 - Prob. 1.32PCh. 1 - Prob. 1.33PCh. 1 - Prob. 1.34PCh. 1 - Prob. 1.35PCh. 1 - Prob. 1.36PCh. 1 - Prob. 1.37PCh. 1 - Prob. 1.38PCh. 1 - Prob. 1.39PCh. 1 - Prob. 1.40PCh. 1 - Prob. 1.41PCh. 1 - Prob. 1.42PCh. 1 - Prob. 1.43PCh. 1 - Prob. 1.44PCh. 1 - Prob. 1.45PCh. 1 - Prob. 1.46PCh. 1 - Prob. 1.47PCh. 1 - Prob. 1.48PCh. 1 - Prob. 1.49P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- T F The specific weight of a fluid is the product of the fluid's density and the acceleration due to gravity. Stronger surface tension leads to higher capillary rise. Absolute pressures are frequently negative. If the pressure of fluid drops below the vapor pressure of that fluid at that temperature, the fluid will cavitate. F F T F F Density can be measured in lb;/ft° in the English system of units. For a hydrostatic incompressible fluid, pressure is independent of depth. A fluid with a high bulk modulus of elasticity is more difficult to compress than one with a low bulk modulus of elasticity. Viscosity is caused, in part, by the surface tension within a fluid. A fluid can resist an applied shear stress by deforming. Pressure increases faster with depth in less dense fluids than in more dense fluids. T F F F F Farrow_forwardAn air bubble rises from the bottom of a well where the temperature is 25oC, to the surface where the temperature is 27o If the depth of the well is 5m and the atmospheric pressure is 101.325kPa, determine the following: Initial pressure inside the air bubble (P1). Volume of air bubble at state 1. Volume of air bubble at state 2. Percent increase in volume of the bubble.arrow_forwardAt the beach, atmospheric pressure is 1025 mbar. You dive 20 m down in the ocean and you later climb a hill up to 350 m in elevation. Assume the density of water is about 1000 kg/m³ and the density of air is 1.18 kg/m³. What pressure (in kPa) do you feel in each place?arrow_forward
- Calculate the weight of air (in pounds) contained within a room 23 ft long, 10 ft wide, and 30 ft high. Assume standard atmospheric pressure and temperature of (2,175 lb/ft 2 and 56.0°F, respectively. Note: Specific Heat of Air in English Units, R = 1716 ft*lb/(slug* R) %3Darrow_forwardThe atmospheric pressure at sea level is 101 kPa. If at an elevation 10,000 ft above sea level atmospheric pressure measures 74 kPa. At what elevation (meters) does the pressure become 21 kPa?arrow_forward2. The diameters of the suction and discharge pipes of a pump are 15 and 10 cm, respectively. The discharge pressure is read by a gage at a point 1.5 m above the centerline of the pump and the suction pressure is read by a gage 0.6 m below the centerline. If the pressure gage reads 140 kPa and the suction gage reads a vacuum of 21 cm Hg when gasoline is pumped at the rate of 35 l/sec (sg of gasoline is 0.75) a. Find the energy added by a pump. (. b. Find the power delivered to the fluid in kW. c. Find the required rating horsepower of the pump if it has an efficiency of 75% 0.10 mg Pz=140 kPa 1.5 m 0.6 m KD Pj=-0.21 m Hg 0.15 møarrow_forward
- Please show your solution on a paper with measures of units in every process. At a pressure of 60°F, a motorbike lre is inflated to 33 psig. As it is driven along the C-5 road,the temperature rose by 76°F.Assuming the volume remains constant,determine the final gauge pressure.arrow_forward1.124 ▸ WILEY As shown in Video V1.9, surface tension forces can be strong enough to allow a double-edge steel razor blade to "float" on water, but a single-edge blade will sink. Assume that the surface tension forces act at an angle 0 relative to the water sur- face as shown in Fig. P1.124. (a) The mass of the double-edge blade is 0.64 × 10-³ kg, and the total length of its sides is 206 mm. Determine the value of 0 required to maintain equilibrium be- tween the blade weight and the resultant surface tension force. (b) The mass of the single-edge blade is 2.61 × 10-³ kg, and the total length of its sides is 154 mm. Explain why this blade sinks. Support your answer with the necessary calculations. Blade Surface tension force Karrow_forwardTank B Pam= 101 kPa iv) Figure shows a tank within a tank, each containing air. The absolute pressure in tank A is 267.7 kPa. Pressure gage A is located inside of tank B and reads 140 kPa. The U-tube manometer connected to tank B contains mercury. Determine the absolute pressure in tank B, in kPa and column length, in cm. The atmospheric pressure surrounding tank B is 101 kPa. The acceleration due to gravity is 9.81 m/s?. Tank A. PA - 267.7 kPa Gage A Poen. A140 kPa Mercury (p 13.59 g/em) g=98i misarrow_forward
- Figure P1.33 shows a storage tank holding natural gas. In an adjacent instrument room, a U-tube mercury manometer in communication with the storage tank reads L = 1.0 m. If the atmospheric pressure is 101 kPa, the density of the mercury is 13.59 g/cm³, and g = 9.81 m/s2, determine the pressure of the natural gas, in kPa. Natural gas Fig. P1.33 Instrument roomarrow_forwardIf the specific volume of a certain gas is 0.7848 m^3/kg, what is its specific gravity?arrow_forwardA tank contains 5,810 lbs of water at room temperature. How many hours would it take to empty the tank if a pump removes 1 gallons of water from the tank every minute.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Properties of Fluids: The Basics; Author: Swanson Flo;https://www.youtube.com/watch?v=TgD3nEO1iCA;License: Standard YouTube License, CC-BY
Fluid Mechanics-Lecture-1_Introduction & Basic Concepts; Author: OOkul - UPSC & SSC Exams;https://www.youtube.com/watch?v=6bZodDnmE0o;License: Standard Youtube License