Concept explainers
Describe how pressure switches are connected to start and stop (a) small motors and (b) large motors.
(a)
Explain how does the pressure switches are connected to start and stop small motors.
Answer to Problem 1SQ
The pressure switches are connected directly to start and stop small motors.
Explanation of Solution
Discussion:
In industrial applications, the pressure switches are used to sense pressure. A large variety of pressure switches are available to control the requirements of hydraulic machines or pneumatic machines.
Single-pole pressure switches are most commonly used and Two-pole pressure switches are used only for few applications.
In small motors, the pressure switches are directly connected to the load circuits when the capacities of the contact are sufficient for the load current.
Conclusion:
Thus, the pressure switches are connected directly to start and stop small motors.
(b)
Explain how does the pressure switches are connected to start and stop large motors.
Answer to Problem 1SQ
The pressure switches are connected series with motor starter and line to start and stop large motors.
Explanation of Solution
Discussion:
In industrial applications, the pressure switches are used to sense pressure. A large variety of pressure switches are available to control the requirements of hydraulic machines or pneumatic machines.
Single-pole pressure switches are most commonly used and Two-pole pressure switches are used only for few applications.
In large motors, the pressure switches alone cannot handle the load circuits safely where it must be connected in series with the motor starter coil and line such that the starter can start and stop large motors safely.
Conclusion:
Thus, the pressure switches are connected in series with motor starter and a line are to start and stop large motors.
Want to see more full solutions like this?
Chapter 10 Solutions
Electric Motor Control
- 6.a. When you're taking a PM motor apart you should exercise special care not to damage theA. end bells.B. commutator.C. permanent magnets.D. brush holders.6.b. A PM field servo motor may be equipped with a resolver that is used toA. excite the armature windings.B. create a voltage that increases with velocity.C. prevent the brushes from sparking.D. feed back position information.arrow_forwardWhat is the name of the speed control by varying the flux of the DC motor? a. Flux control method b. Voltage control method c. None of the above d. Armature control methodarrow_forward1- What is the starting torque developed by a split-phase or a capacitor start motor? 2- What is the current in-rush at the time of starting the motor? Does it cause severe fluctuations on the line?arrow_forward
- Can you give me all the different types of DC motor its quite confusing coz some info says it has only 4 which is series , shunt , compount , and permanent magnet which is only under the category of brushed DC motors it doesnt include yet the brushless and the sub category however when you recognize or notice that in flowchart there are several like the one self excited etc I wonder if its an updated version though but I need you to list all of them and explain each and what category or subcategory I mean the overall DC motors even in chatgpt there are some added like universal , stepper , servo , coreless and so on. Explain each one. Pls help me if you could summarize or elaborate all at once so that it would be easy to identify or determine the overall information and additionally per category should have definition as well as the followingarrow_forwardA switched reluctance motor has salient poles on ..................... a. neither stator or rotor b. Stator and rotor c. Rotor only d. Stator onlyarrow_forwardIf the field winding of a DC shunt motor gets disconnected while in normal operation the speed will decrease to a tremendously low value and the motor may get stop. * O True O Falsearrow_forward
- asap Draw the schematic diagram of a Six-Point Drum Switches that operate the long shunt compound dc motor in reverse –forward operation. Connect all the parts into the Drum Switch terminals only not in the outside of the Drum Switches.arrow_forwardExplain how does the current will be reduced during the starting of the motor.arrow_forward1. Soru Which DC Motor(s) is(are) suitable for constant speed loads? (You can select multiple types) A) Permanent Magnet DC Motor B) Compound DC Motor O C) Shunt DC Motor O D)Series DC Motorarrow_forward
- F1. DC series motors have no natural speed limit and should never be operated in a no-load condition. a) true b) false F2. should never be used to connect a DC series motor to a load. a) Belts b) Chains c) either "a" or "b" d) neither "a" nor "b" F3. A gearmotor is one way of making a DC series motor so it is connected directly to a mechanical load. a) true b) falsearrow_forward5. How does the saturation in the machine affect the speed of shunt motor?arrow_forwardQ/ When a series dc motor is operated without a load, which of the following conditions occurs? * Ans 1- The armature draws excessive current 2- The armature speeds out of control 3- The armature will not turn 4-The voltage requirement increasesarrow_forward