About 75 percent of hydrogen for industrial use is produced by the steam-reforming process. This process is carried out in two stages called primary and secondary reforming. In the primary stage, a mixture of steam and methane at about 30 atm is heated over a nickel catalyst at 800°C to give hydrogen and carbon monoxide:
The secondary stage is carried out at about 1000°C, in the presence of air, to convert the remaining methane to hydrogen:
(a) What conditions of temperature and pressure would favor the formation of products in both the primary and secondary stage? (b) The equilibrium constant Kc for the primary stage is 18 at 800°C. (i) Calculate KP for the reaction. (ii) If the partial pressures of methane and steam were both 15 atm at the start, what are the pressures of all the gases at equilibrium?
(a)
Interpretation:
The conditions of temperature and pressure which would favour the formation of products in both the primary and secondary stage has to be calculated using the data.
Concept Introduction:
Endothermic reaction:
In an endothermic reaction, heat will be a reactant. Therefore, increasing the temperature will shift the reaction from reactant side to the product side and the value of equilibrium constant will increases.
Exothermic reaction:
In an exothermic reaction, heat will be a product. Therefore, increasing the temperature will shift the reaction from product side to the reactant side and the value of equilibrium constant will decreases.
Explanation of Solution
Given data:
The reactions at primary stage and at the secondary stage are given below:
The reaction at primary stage has a temperature of
The both reactions are endothermic
If the reactions are endothermic, heat will be the reactant and high temperatures will favour the product side.
Therefore, high temperature is maintained at steam-reforming process.
Examining the reactions, it can be seen that number of moles of products is greater than the number of moles of reactants. Therefore, the expectation is that the products will be favoured at low pressures.
The reality is that the reactions are carried out at high pressures. It is for the production of higher yields of ammonia by the hydrogen gas produced which requires a high pressure.
(b)
Interpretation:
The equilibrium constant
Concept Introduction
Equilibrium constant at constant pressure:
It is used to express the relationship between product pressures and reactant pressures.
For a general reaction,
R- Gas constant
T- Temperature
Explanation of Solution
Given data:
The reaction is given below:
Equilibrium constant
The
The pressure of all the gases at equilibrium has to be calculated.
The amount of
The ICE table for the reaction is given below
Substituting the values in the equilibrium constant equation,
Taking the square root of both sides,
The value of x can be obtained by solving the quadratic equation
The pressure at equilibrium can be calculated as follows:
Want to see more full solutions like this?
Chapter 14 Solutions
Chemistry
- 12.103 Methanol, CH3OH, can be produced by the reaction of CO with H2, with the liberation of heat. All species in the reaction are gaseous. What effect will each of the following have on the equilibrium concentration of CO? (a) Pressure is increased, (b) volume of the reaction container is decreased, (c) heat is added, (d) the concentration of CO is increased, (e) some methanol is removed from the container, and (f) H2 is added.arrow_forwardFor the reaction N2(g)+3H2(g)2NH3(g) show that Kc = Kp(RT)2 Do not use the formula Kp = Kc(RT)5n given in the text. Start from the fact that Pi = [i]RT, where Pi is the partial pressure of substance i and [i] is its molar concentration. Substitute into Kc.arrow_forwardKc = 5.6 1012 at 500 K for the dissociation of iodine molecules to iodine atoms. I2(g) 2 I(g) A mixture has [I2] = 0.020 mol/Land [I] = 2.0 108 mol/L. Is the reaction at equilibrium (at 500 K)? If not, which way must the reaction proceed to reach equilibrium?arrow_forward
- Write equilibrium constant expressions for the following reactions. For gases, use either pressures or concentrations. (a) 2 H2O2(g) 2 H2O(g) + O2(g) (b) CO(g) + O2g CO2(g) (c) C(s) + CO2(g) 2 CO(g) (d) NiO(s) + CO(g) Ni(s) + CO2(g)arrow_forwardA solution is prepared by dissolving 0.050 mol of diiodocyclohexane, C5H10I2, in the solvent CCl4.The total solution volume is 1.00 L When the reaction C6H10I2 C6H10 + I2 has come to equilibrium at 35 C, the concentration of I2 is 0.035 mol/L. (a) What are the concentrations of C6H10I2 and C6H10 at equilibrium? (b) Calculate Kc, the equilibrium constant.arrow_forwardDistinguish between the terms equilibrium constant and reaction quotient. When Q = K, what does this say about a reaction? When Q K, what does this say about a reaction? When Q K. what does this say about a reaction?arrow_forward
- Introductory Chemistry: A FoundationChemistryISBN:9781285199030Author:Steven S. Zumdahl, Donald J. DeCostePublisher:Cengage LearningChemistry & Chemical ReactivityChemistryISBN:9781337399074Author:John C. Kotz, Paul M. Treichel, John Townsend, David TreichelPublisher:Cengage LearningChemistry & Chemical ReactivityChemistryISBN:9781133949640Author:John C. Kotz, Paul M. Treichel, John Townsend, David TreichelPublisher:Cengage Learning
- General Chemistry - Standalone book (MindTap Cour...ChemistryISBN:9781305580343Author:Steven D. Gammon, Ebbing, Darrell Ebbing, Steven D., Darrell; Gammon, Darrell Ebbing; Steven D. Gammon, Darrell D.; Gammon, Ebbing; Steven D. Gammon; DarrellPublisher:Cengage LearningChemistry: The Molecular ScienceChemistryISBN:9781285199047Author:John W. Moore, Conrad L. StanitskiPublisher:Cengage LearningChemistry for Engineering StudentsChemistryISBN:9781337398909Author:Lawrence S. Brown, Tom HolmePublisher:Cengage Learning