Physics for Scientists and Engineers: Foundations and Connections
1st Edition
ISBN: 9781133939146
Author: Katz, Debora M.
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 14.4, Problem 14.5CE
Imagine two vertical rods initially of equal length. One rod is made of steel, and the other is made of rubber. Suppose you hang a load of the same mass from each rod. You are just able to eyeball the stretch in the rubber rod. Do you expect to notice any stretch in the steel rod? Explain.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A 480 mm long thighbone (femur), which is the largest and longest bone in the human body, has a cross sectional area of 7.7 × 10–4 m2. A safety factor of 4 applies and the maximum compressional stress that a bone can withstand is 1.6 × 108 N/m2 before it breaks. Young’s Modulus (E ) of a bone at room temperature is 15 × 109 Pa. How much will it compress to support a weight of 1.2 × 105 N?
Nylon strips are fused to glass plates. When moderately heated the nylon
will become soft while the glass stays approximately rigid. Determine the
average shear strain in the nylon due to the load P when the assembly
deforms as indicated.
2 mm
3 mm
5 mm
3 mm
5 mm
3 mm
0.197 rad
0.297 rad
O 0.397 rad
O 0.125 rad
O none of the above
A 35.0 kg mass hangs from a steel wire. The unloaded length of the wire is 3.05 m and it has a diameter of 1.024 mm. How much is the
wire stretched (mm) when the mass is added? Young's modules for steel is 2.00 x 10¹¹ N/m².
O 19.9
O 7.44
O 0.651
O 6.35
O 13.8
O 0.273
O 3.18
O 5.35
4.28
O 1.59
Chapter 14 Solutions
Physics for Scientists and Engineers: Foundations and Connections
Ch. 14.1 - A rubber duck floats in a bathtub. Imagine moving...Ch. 14.1 - Prob. 14.2CECh. 14.2 - CASE STUDY Hanging a Plane from a Single Point In...Ch. 14.2 - Prob. 14.4CECh. 14.4 - Imagine two vertical rods initially of equal...Ch. 14 - What Is Static Equilibrium? Problems 13 are...Ch. 14 - Prob. 2PQCh. 14 - Two identical balls are attached to a...Ch. 14 - While working on homework together, your friend...Ch. 14 - Consider the sketch of a portion of a...
Ch. 14 - Prob. 6PQCh. 14 - Prob. 7PQCh. 14 - Prob. 8PQCh. 14 - The keystone of an arch is the stone at the top...Ch. 14 - Prob. 10PQCh. 14 - Stand straight and comfortably with your feet...Ch. 14 - Prob. 12PQCh. 14 - Prob. 13PQCh. 14 - Prob. 14PQCh. 14 - Prob. 15PQCh. 14 - Prob. 16PQCh. 14 - Prob. 17PQCh. 14 - Prob. 18PQCh. 14 - Prob. 19PQCh. 14 - Prob. 20PQCh. 14 - Prob. 21PQCh. 14 - The inner planets of our solar system are...Ch. 14 - Two Boy Scouts, Bobby and Jimmy, are carrying a...Ch. 14 - Prob. 24PQCh. 14 - A painter of mass 87.8 kg is 1.45 m from the top...Ch. 14 - Consider the situation in Problem 25. Tests have...Ch. 14 - Children playing pirates have suspended a uniform...Ch. 14 - Prob. 28PQCh. 14 - Prob. 29PQCh. 14 - A 5.45-N beam of uniform density is 1.60 m long....Ch. 14 - A wooden door 2.1 m high and 0.90 m wide is hung...Ch. 14 - A 215-kg robotic arm at an assembly plant is...Ch. 14 - Problems 33 and 34 are paired. One end of a...Ch. 14 - For the uniform beam in Problem 33, find the...Ch. 14 - Prob. 35PQCh. 14 - A square plate with sides of length 4.0 m can...Ch. 14 - Prob. 37PQCh. 14 - At a museum, a 1300-kg model aircraft is hung from...Ch. 14 - A uniform wire (Y = 2.0 1011 N/m2) is subjected...Ch. 14 - A brass wire and a steel wire, both of the same...Ch. 14 - In Example 14.3, we found that one of the steel...Ch. 14 - A carbon nanotube is a nanometer-scale cylindrical...Ch. 14 - A nanotube with a Youngs modulus of 1.000 1012 Pa...Ch. 14 - Consider a nanotube with a Youngs modulus of 2.130...Ch. 14 - Prob. 45PQCh. 14 - Use the graph in Figure P14.46 to list the three...Ch. 14 - Prob. 47PQCh. 14 - A company is testing a new material made of...Ch. 14 - Prob. 49PQCh. 14 - Prob. 50PQCh. 14 - Prob. 51PQCh. 14 - Prob. 52PQCh. 14 - Prob. 53PQCh. 14 - Prob. 54PQCh. 14 - Prob. 55PQCh. 14 - Prob. 56PQCh. 14 - A copper rod with length 1.4 m and cross-sectional...Ch. 14 - Prob. 58PQCh. 14 - Prob. 59PQCh. 14 - Bruce Lee was famous for breaking concrete blocks...Ch. 14 - Prob. 61PQCh. 14 - Prob. 62PQCh. 14 - Prob. 63PQCh. 14 - A One end of a metal rod of weight Fg and length L...Ch. 14 - Prob. 65PQCh. 14 - A steel cable 2.00 m in length and with...Ch. 14 - Prob. 67PQCh. 14 - Prob. 68PQCh. 14 - Prob. 69PQCh. 14 - Prob. 70PQCh. 14 - Prob. 71PQCh. 14 - Prob. 72PQCh. 14 - Prob. 73PQCh. 14 - We know from studying friction forces that static...Ch. 14 - Ruby, with mass 55.0 kg, is trying to reach a box...Ch. 14 - An object is being weighed using an unequal-arm...Ch. 14 - Prob. 77PQCh. 14 - A massless, horizontal beam of length L and a...Ch. 14 - A rod of length 4.00 m with negligible mass is...Ch. 14 - A rod of length 4.00 m with negligible mass is...Ch. 14 - A horizontal, rigid bar of negligible weight is...Ch. 14 - Prob. 82PQCh. 14 - Prob. 83PQCh. 14 - Prob. 84PQCh. 14 - Prob. 85PQ
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.Similar questions
- The lintel of prestressed reinforced concrete in Figure P12.27 is 1.50 m long. The concrete encloses one steel reinforcing rod with cross-sectional area 1.50 cm2. The rod joins two strong end plates. The cross-sectional area of the concrete perpendicular to the rod is 50.0 cm2. Youngs modulus for the concrete is 30.0 109 N/m2. After the concrete cures and the original tension T1 in the rod is released, the concrete is to be under compressive stress 8.00 106 N/m2. (a) By what distance will the rod compress the concrete when the original tension in the rod is released? (b) What is the new tension T2 in the rod? (c) The rod will then be how much longer than its unstressed length? (d) When the concrete was poured, the rod should have been stretched by what extension distance from its unstressed length? (e) Find the required original tension T1 in the rod. Figure P12.27arrow_forwardA copper rod with length 1.4 m and cross-sectional area 2.0 cm2 is fastened to a steel rod of length L and cross-sectional area 1.0 cm2. The compound structure is pulled on each side by two forces of equal magnitude 6.00 104 N (Fig. P14.57). Find the length L of the steel rod if the elongations (L) of the two rods are equal. Use the values Ysteel = 2.0 1011 Pa and YCu = 1.1 1011 Pa. FIGURE P14.57arrow_forwardUse the graph in Figure P14.46 to list the three materials from greatest Youngs modulus to smallest. Explain your reasoning. FIGURE P14.46arrow_forward
- Assume Youngs modulus for bone is 1.50 1010 N/m2. The bone breaks if stress greater than 1.50 108 N/m2 is imposed on it. (a) What is the maximum force that can be exerted on the femur bone in the leg if it has a minimum effective diameter of 2.50 cm? (b) If this much force is applied compressively, by how much does the 25.0-cm-long bone shorten?arrow_forwardA horizontal, rigid bar of negligible weight is fixed against a vertical wall at one end and supported by a vertical string at the other end. The bar has a length of 50.0 cm and is used to support a hanging block of weight 400.0 N from a point 30.0 cm from the wall as shown in Figure P14.81. The string is made from a material with a tensile strength of 1.2 108 N/m2. Determine the largest diameter of the string for which it would still break. FIGURE P14.81arrow_forwardConsider a nanotube with a Youngs modulus of 2.130 1012 N/m2 that experiences a tensile stress of 5.3 1010 N/m2. Steel has a Youngs modulus of about 2.000 1011 Pa. How much stress would cause a piece of steel to experience the same strain as the nanotube?arrow_forward
- Two racquetballs, each having a mass of 170 g, are placed in a glass jar as shown in Figure P12.43. Their centers lie on a straight line that makes a 45 angle with the horizontal. (a) Assume the walls are frictionless and determine P1, P2, and P3. (b) Determine the magnitude of the force exerted by the left ball on the right ball. Figure P12.43arrow_forwardA spring 1.50 m long with force constant 475 N/m is hung from the ceiling of an elevator, and a block of mass 10.0 kg is attached to the bottom of the spring. (a) By how much is the spring stretched when the block is slowly lowered to its equilibrium point? (b) If the elevator subsequently accelerates upward at 2.00 m/s2, what is the position of the block, taking the equilibrium position found in part (a) as y = 0 and upwards as the positive y-direction. (c) If the elevator cable snaps during the acceleration, describe the subsequent motion of the block relative to the freely falling elevator. What is the amplitude of its motion?arrow_forwardA 100-N weight is attached to a free end of a metallic wire that hangs from the ceiling. When a second 100-N weight is added to the wire, it stretches 3.0 mm. The diameter and the length of the wire are 1.0 mm and2.0 m, respectively. What is Young’s modulus of the metal used to manufacture the wire?arrow_forward
- Review. A mixing beater consists of three thin rods, each 10.0 cm long. The rods diverge from a central hub, separated from each other by 120, and all turn in the same plane. A ball is attached to the end of each rod. Each ball has cross-sectional area 4.00 cm2 and is so shaped that it has a drag coefficient of 0.600. Calculate the power input required to spin the beater at 1 000 rev/min (a) in air and (b) in water.arrow_forwardThe legs of a weight lifter must ultimately support the weights he has lifted. A human tibia (shinbone) has a circular cross section of approximately 3.6 cm outer diameter and 2.5 cm inner diameter. (The hollow portion contains marrow. ) if a 90 kg lifter stands on both legs, what is the heaviest weight he can lift without breaking his legs, assuming that the breaking stress of the bone is 200 MPa?arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning
Principles of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
University Physics Volume 1PhysicsISBN:9781938168277Author:William Moebs, Samuel J. Ling, Jeff SannyPublisher:OpenStax - Rice University
Physics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
Physics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
College PhysicsPhysicsISBN:9781285737027Author:Raymond A. Serway, Chris VuillePublisher:Cengage Learning
Physics for Scientists and Engineers: Foundations...
Physics
ISBN:9781133939146
Author:Katz, Debora M.
Publisher:Cengage Learning
Principles of Physics: A Calculus-Based Text
Physics
ISBN:9781133104261
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
University Physics Volume 1
Physics
ISBN:9781938168277
Author:William Moebs, Samuel J. Ling, Jeff Sanny
Publisher:OpenStax - Rice University
Physics for Scientists and Engineers
Physics
ISBN:9781337553278
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Physics for Scientists and Engineers with Modern ...
Physics
ISBN:9781337553292
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
College Physics
Physics
ISBN:9781285737027
Author:Raymond A. Serway, Chris Vuille
Publisher:Cengage Learning
An Introduction to Stress and Strain; Author: The Efficient Engineer;https://www.youtube.com/watch?v=aQf6Q8t1FQE;License: Standard YouTube License, CC-BY