Concept explainers
Fiberglass is a popular, economical, and fairly effective building insulation. It consists of fine glass fibers—often including recycled glass—formed loosely into rectangular slabs or rolled into blankets (Fig. 16.18). One side is often faced with heavy paper or aluminum foil. Fiberglass insulation comes in thicknesses compatible with common building materials—for example, 3.5 inch and 6 inch for wood-framed walls. Standard 6-inch fiberglass has an R-factor of 19.
Since fiberglass insulation is readily compressible, you could squash two slabs initially 6 inches wide into a 6-inch wall space. This would
- a. double the overall R-factor.
- b. increase the overall R-factor but not double it.
- c. decrease the overall R-factor.
- d. not change the overall R-factor.
Want to see the full answer?
Check out a sample textbook solutionChapter 16 Solutions
Essential University Physics: Volume 1 (3rd Edition)
Additional Science Textbook Solutions
Physics for Scientists and Engineers: A Strategic Approach with Modern Physics (4th Edition)
Essential University Physics: Volume 2 (3rd Edition)
Introduction to Electrodynamics
Glencoe Physical Science 2012 Student Edition (Glencoe Science) (McGraw-Hill Education)
Modern Physics
Physics: Principles with Applications
- A copper wire has a cross section of 2.5 mm^2 and a length of 2 meters. What is the electrical resistant at 20 degrees Celsius?arrow_forwardA person eats a dessert that contains 170 Calories. (This "Calorie" unit, with a capital C, is the one used by nutritionists; 1 Calorie = 4186 J. See Section 12.7.) The skin temperature of the person is 36 °C and that of her environment is 18 °C. The emissivity of her skin is 0.71 and its surface area is 1.5 m2. How many hours would it take her to emit a net radiant energy from her body that is equal to the energy contained in this dessert?arrow_forwardA pure aluminum plate is part of a heat shield for a manufacturing process. The aluminum plate has a thickness of 3.60 mm. The aluminum plate is insulated (on one side only) with Board and Slab insulation (Cellular glass, density of 145 kg/m3) 6.00 cm thick; which in turn is covered with a layer of Particle board (high density) 1.00 cm thick (The composite wall goes: aluminum/cellular glass insulation/Particle board). The temperature on the exposed surface of the aluminum plate is measured to be 78.0°C, while the outside surface of the Particle board is exposed to convection, T = 22.0°C, h = 17.0 W/(m2-K). The plate has dimensions of 11.50 m long by 3.50 m tall. • Draw and label a sketch of this system. Includedimensions, known temperatures, etc. • Draw and completely label the corresponding 1-Dsteady-state conduction resistor diagram. • Determine the heat transfer rate through thiscomposite plate. • Calculate the temperature at the Cellular Glassinsulation/Particle board interface.arrow_forward
- A thermal window, with an area of 6.0m ^ 2, is constructed of two layers of glass, each 4.0mm thick, separated from each other by a 5.0mm air gap. If the inner surface is at 20.0 ° C and the outer surface is at -5.0 ° C, what is the rate of energy transfer by conduction through the window? The thermal conductivity of glass is 0.8 W⁄ (m. ° C) and that of air is 0.023 W⁄ (m. ° C)arrow_forwardThe table below gives the results of measuring the electrical conductivity C of glass at temperature T degrees Fahrenheit. 86 148 166 188 202 210 0.004 0.018 0.029 0.051 0.073 0.090 Use regression to find the exponential function C=ae bT that will satisfy the given table. Find the value of Cif T = 197.1.arrow_forwardA classroom has dimensions 8.00 m x 10.00 m x 3.00 m. A 1000 W electric space heater is being used to warm the room from 5.00°C to 20.00°C on a cold morning. If the density of air is 1.29 kg/m°, and the specific heat capacity of air is 1004 J/(kg-K), how long will it take to heat the room? Assume no loss of thermal energy to the surroundings. A) 1.30 minutes B) 241 minutes C) 45.3 minutes O D) 77.7 minutesarrow_forward
- A walrus transfers energy by conduction through its blubber at the rate of 150 W when immersed in −1.00 °C water. The walrus’s internal core temperature is 37.0 °C , and it has a surface area of 2.00 m2 . What is the average thickness of its blubber, which has the conductivity of fatty tissues without blood?arrow_forwardAn electric stove burner has surface area 325 cm² and emissivity e = 1. The burner consumes 1500 W and is at 900 K. If room temperature is 300 K, what fraction of the burner's heat loss is from radiation?arrow_forward1034. The motion of a particle starting from rest is governed by the a-t curve shown in Fig. P-1034. Sketch the v-t and s-t curves. Determine the displacement at t = 9 sec. Ans. = 228 ft 8arrow_forward
- You have a mystery substance, length 2.0 m, cross section 0.40 m2 , and apply atemperature difference of 69°C across its length. If the substance conducts 1000.0 J ofheat in 0.50 sec, what is its thermal conductivity?arrow_forwardWhat is the rate of heat transfer by radiation, with an unclothed person standing in a dark room whose ambient temperature is 22.0ºC . The person has a normal skin temperature of 33.0ºC and a surface area of 1.50 m2 . The emissivity of skin is 0.97 in the infrared, where the radiation takes place.arrow_forwardA 10-in nominal pipe (outside diameter = 10.75in) is covered with a composite pipe insulation consisting of 2.0 in of insulation I placed next to the pipe and 1.5 in of insulation II placed upon insulation I. Assume that the inner and outer surface temperatures of the composite insulation are 900F and 150F respectively, and that the thermal conductivity of material I is 0.05 BTU/hr-ft-F and for material II is 0.039 BTU/hr-ft-F. What is the individual thermal resistance of insulation I?arrow_forward
- Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning