Concept explainers
a)
Find the angular velocity of the bar after the impact.
a)
Answer to Problem 17.130P
The angular velocity of the bar after the impact is
Explanation of Solution
Given information:
The weight
The radius
The weight
The length
The angular velocity
The velocity
Calculation:
Consider G is the mass center of rod AB.
Find the mass
Substitute 2 lb for
Find the moment of inertia
Substitute
Consider C be the mass center of the sphere.
Find the mass of the sphere
Substitute 3 lb for
Find the moment of inertia
Substitute
The rod and sphere have same angular velocity
Sketch the geometry of the sphere and the uniform rod as shown in Figure (1).
Refer Figure (1),
Find the distance R.
Substitute 10 in. for L and 3 in. for r.
Find the angle
Substitute 10 in. for L and 3 in. for r.
Find the velocity
Substitute 10 in. for L and
Write the velocity
Write the velocity
Consider the conservation of momentum principle.
Sketch the impulse and momentum diagram of the system as shown in Figure (2).
Refer Figure (2).
Take moment about A (positive sign in clockwise direction).
Substitute
Substitute
Thus, the angular velocity of the bar after the impact is
b)
Find the components of the reactions at A.
b)
Answer to Problem 17.130P
The horizontal component of the reactions at A is
The vertical component of the reactions at A is
Explanation of Solution
Calculation:
Find the normal acceleration
Substitute 10 in. for L and
Write the equation of tangential acceleration
Here,
Substitute 10 in. for L.
Find the normal acceleration
Substitute 0.8700 ft for R and
Write the equation of tangential acceleration
Substitute 0.8700 ft for R.
Sketch the free body diagram of the uniform rod and sphere as shown in Figure (1).
Refer Figure (3).
Take moment about A (positive sign in clockwise direction).
Substitute
Substitute 2 lb for
Find the tangential acceleration
Substitute
Find the tangential acceleration
Substitute
Refer Figure (3),
Consider the horizontal component forces.
Here,
Substitute
Thus, the horizontal component of the reactions at A is
Consider vertical components of forces.
Here,
Substitute 2 lb for
Thus, the vertical component of the reactions at A is
Want to see more full solutions like this?
Chapter 17 Solutions
Vector Mechanics for Engineers: Statics and Dynamics
- 7. (a) A uniform prismatic rod of length I and mass m is placed in a vertical position with one end on a smooth horizontal floor. It is then let go, and it falls to the floor from rest in the vertical position. Assuming that the rod never loses contact with the floor, derive an expression for its angular velocity at any position as shown in Figure 7(a). (b) ( =0 Figure 7(a) Determine the height h at which the billiard ball of radius r must be struck so that no frictional force develops between the ball and the table at 4 as shown in Figure 7(b). Assume that the cue only exerts a horizontal force P on the ball. Take IG of the ball equal to (2/5)mr², where m is the mass of the ball. Figure 7(b)arrow_forwardConsider the mechanism shown. Members PQ and QR are joined by a hinge at Q. End P of member PQ is pin-supported and end R of member QR is constrained to move along a horizontal surface. Member PQ rotates clockwise at a constant rate of 12 rad/s. Member QR rotates counterclockwise at a rate of 3.84 rad/s. Which of the following gives the closest value to the magnitude of the angular acceleration of rod QR? 9.16, 6.18, 1.609, 35.2 rad/s^2?? Which of the following gives the closest value to the magnitude of the acceleration of point R? 3.13, 9.89, 10.28, 12.88 m/s^2??arrow_forwardA drum of radius r, = 3 in. is mounted on a cylinder of radius r, = 4 in. A cord is wound around the drum, and its extremity D is pulled to the left with a constant velocity of 5 in./s, causing the cylinder to roll without sliding. Determine: = of 1. The angular velocity of the cylinder. 2. The velocity of the center of the cylinder A. riin. r2 in. D Select one: O A. W = 2 rad/s; and VA = 6 in/s. O B.w = 4 rad/s; and VA = 16 in/s. OC.w=5 rad/s; and VA = 25 in/s. O D.w= 5 rad/s: and V = 15 in/s. 1:06 PM O 4) G ENG 4/17/2021arrow_forward
- Two panels A and B are attached with hinges to a rectangular plate and held by a wire as shown. The plate and the panels are made of the same material and have the same thickness. The entire assembly is rotating with an angular velocity w0 when the wire breaks. Determine the angular velocity of the assembly after the panels have come to rest against the plate.arrow_forwardA 240-lb block is suspended from an inextensible cable which is wrapped around a drum of 1.25-ft radius rigidly attached to a flywheel. The drum and flywheel have a combined centroidal moment of intertia of 10.5 lb-ft-s^2. At the instant shown, the velocity of the block is 6 ft/s directed downward. The bearing at A as a frictional moment of 60 lb-ft. What is the kinetic energy of the system after the block moved after 4ft? (in ft-lb)arrow_forwardA 18-kg rear hatch of a vehicle opens as shown in the figure and can be modeled as a uniform 0.6-m long slender rod. Knowing that the tailgate is released from rest in the position shown in the figure, determine the angular velocity of the tailgate as it impacts the car body.arrow_forward
- Consider a steel plate of mass m with dimensions L and w that is equally supported by two ball bearings (one on each end of the shaft shown at pointa A and B). At the instant shown below, the plate is released from rest. Part A: Determine an expression for the plate's angular acceleration magnitude a at this in- stant. (Hint: Use Euler's 2nd Law for pinned rotation and the parallel axis theorem.) Part B: Show that the magnitude of the reaction force at each bearing at this instant is R = mg/8. (Hint: Use the kinematics to relate the acceleration of the center of mass G to the angular acceleration. Use Euler's 1st Law to find the reaction forces with the acceleration you determined. As viewed from the side there are two forces acting on the system weight and two reaction forces both pointing upward at the same location.) A foye مر B L २arrow_forwardA homogeneous rectangular plate weighing 40 lb is suspended from two frictionless pins A and B. If pin B is suddenly removed, determine:a) the components of the reaction at pin A immediately after the pin is removed,b) the angular velocity of the plate after the plate has rotated thirty degrees in the clockwise direction.arrow_forward2. A 15-kg slender bar OA is released from rest in the purely vertical position* and compresses the spring of stiffness k = 20 kN/m as the horizontal position is passed. The spring height h can be adjusted via a thumb screw. a. If we desire the bar to have an angular velocity of 4 rad/s as it crosses the horizontal, what should h be 600 mm set to? b. How does the design choice of the position x affect these calculations? *Parallax of my scan misleads a little. The bar starts at a straight vertical position. x = 400 mmarrow_forward
- Q#1: Four masses A, B, C and D carried by a rotating shaft at radii 80 mm, 100mm, 160 and 120 mm respectively are completely balanced. Masses B, C and D are 8 kg, 4 kg and 3kg respectively. Determine the mass A and the relative angular positions of the four masses if each of the plane are spaced 500 mm apart.arrow_forwardThe ends of a 9-lb bar AB are constrained to move along slots cut in a vertical plate as shown. A resource of constant k = 3 lb/in. is attached to end A such that its tension is zero when e=0. If the bar is released from rest when e = 0, determine the angular velocity of the bar and the velocity of end B when =30°arrow_forwardArm ACB rotates about Point Cwith an angular velocity of 39 radis counterclockwise. Two friction disks A and Bare pinned at their centers to arm ACB as shown. Know that the disks roll without slipping at the surfaces of contact. 2.4 in. 1.2 in. 0.9 in. 1.5 in. 0.6 in. D Determine the angular velocity of disk B. The angular velocity of disk B is radis . Determine the angular velocity of disk A. The angular velocity of disk A is [ rad/s O Determine the angular velocity of disk A. The angular velocity of disk A is rad/s O.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY