(a)
Interpretation:
Whether
Concept Introduction:
Intermolecular forces are forces that are responsible for interaction between molecules. Such forces include both attractive as well as repulsive forces.
Types of intermolecular forces:
1. Ion-dipole forces: These forces come into play when ions interact with polar molecules. Ion gets attracted to oppositely charged end of polar molecule.
2. Dipole-dipole forces: These forces arise when there is interaction between oppositely charged ends of different dipoles.
3. London forces: These forces exist when there is interaction between nonpolar molecules. There occurs distortion in symmetry of electron clouds when two nonpolar molecules come closer to each other. Such forces exist in all molecules and therefore London forces are called universal.
4. Hydrogen bonding: This intermolecular force exists when hydrogen atoms are connected to highly electronegative elements like
(b)
Interpretation:
Whether
Concept Introduction:
Refer to part (a).
(c)
Interpretation:
Whether
Concept Introduction:
Refer to part (a).
(d)
Interpretation:
Whether
Concept Introduction:
Refer to part (a).
Want to see the full answer?
Check out a sample textbook solutionChapter 3 Solutions
Chemical Principles: The Quest for Insight
- (2) A hypothetical tetrahedral crystal has the following lattice parameters: a = b = 0.40 nm, c = 0.5 nm, a = B = y = 90°. Please write the indices of all planes/directions that belong to the family of (i) {100} (5%) and (ii) (5%).arrow_forwardWrite the difference between ferromagnetism and anti-ferromagnetism.arrow_forward(a) Magnesium (Mg) has a hexagonal close-packed (HCP) crystal structure with the lattice parameter of a = 0.321 nm and c= 0.521 nm and the atomic radius is 0.173 nm. (i) What is the number of atoms per unit cell in HCP structure? (ii) Determine the atomic packing factor of the Mg unit cell. (iii) Is Mg containing an ideal atomic packing factor? You may justify your answer by evaluating the HCP c/a ratio. Subsequently, will slip be harder in Mg compared to the ideal HCP structure? Justify your answer.arrow_forward
- (a) How do the viscosity and surface tension of liquids change as intermolecular forces become stronger? (b) How do the viscosity and surface tension of liquids change as temperature increases? Accounts for these trendsarrow_forward(b) Using the Crystallographer's formula to determine the density (in g/cm³) of Po: ρ = Σ Ζ * Μ Vell* N You must know that a primitive cubic cell has Z = 1 Since Po is a metal, the value of "i" = 1, since it's the only entity! MM of Po= 208.998 g/mol Vcell (in cm³) = a³ Vcell (3.36 x 10-8 cm)³ = 3.793 x 10-23 cm³ N = 6.022 x 1023 atoms/mol Thus: p = (1 atom/cell) (208.998 g/mol) = 9.16 g/cm³ (3.793 x 10-23 cm³) (6.022 x 1023)arrow_forwardA 0.640 g sample of a metal, M, reacts completely with sulfuric acid according to M(s) + H,SO,(aq) – MSO, (aq) + H,(g) A volume of 291 mL of hydrogen is collected over water; the water level in the collecting vessel is the same as the outside level. Atmospheric pressure is 756.0 Torr, and the temperature is 25 °C. The vapor pressure of water at 25 °C is 23.8 Torr. Calculate the molar mass of the metal. molar mass: g/mol Question Source: McQuarrie, Rock, And Gallogly 4e - General Chemsitry | Pubarrow_forward
- Neon and HF have approximately the same molecular mass. (a) Explain why the boiling point of Neon and HF differ. (b) Compare the change in the boiling points of Ne, Ar, Kr, and Xe with the change of the boiling points of HF, HCl, HBr, and HI, and explain the difference between the changes with increasing atomic or molecular mass.arrow_forwardAt standard temperature and pressure, the molar volumesof Cl2 and NH3 gases are 22.06 and 22.40 L, respectively.(a) Given the different molecular weights, dipole moments,and molecular shapes, why are their molar volumes nearlythe same? (b) On cooling to 160 K, both substances formcrystalline solids. Do you expect the molar volumes todecrease or increase on cooling the gases to 160 K? (c) Thedensities of crystalline Cl2 and NH3 at 160 K are 2.02 and0.84 g>cm3, respectively. Calculate their molar volumes.(d) Are the molar volumes in the solid state as similar asthey are in the gaseous state? Explain. (e) Would you expectthe molar volumes in the liquid state to be closer to thosein the solid or gaseous state?arrow_forwardA 0.580 g sample of a metal, M, reacts completely with sulfuric acid according to M(s) + H,SO, (aq) – MSO, (aq) + H, (g) A volume of 225 mL of hydrogen is collected over water; the water level in the collecting vessel is the same as the outside level. Atmospheric pressure is 756.0 Torr, and the temperature is 25 °C. The vapor pressure of water at 25 °C is 23.8 Torr. Calculate the molar mass of the metal. molar mass: 63.1189 g/molarrow_forward
- Which of the following set of compounds form an ionic solid, a molecular solid, and a covalent network solid, in that order? (A) Na2O, Na2O2, SiO2; (B) Na2O, MgO, Al2O3; (C) BaO, BaO2, CO2; (D) CaO, SO2, SiO2;arrow_forwardNeon and HF have approximately the same molecular masses.(a) Explain why the boiling points of Neon and HF differ.(b) Compare the change in the boiling points of Ne, Ar, Kr, and Xe with the change of the boiling points of HF, HCl, HBr, and HI, and explain the difference between the changes with increasing atomic or molecular mass.arrow_forward(a) Identify the major phases (ice, water, vapor) on the unary phase diagram of H2O below.arrow_forward
- Introduction to General, Organic and BiochemistryChemistryISBN:9781285869759Author:Frederick A. Bettelheim, William H. Brown, Mary K. Campbell, Shawn O. Farrell, Omar TorresPublisher:Cengage Learning