Fully developed conditions are known to exist for water flowing through a 25-nim-diameer tube at 0.01 kg/s and
The maximum velocity of water inside the tube and pressure gradient along the flow.
Answer to Problem 8.1P
The maximum velocity of water inside the tube is
Explanation of Solution
Given:
The diameter of the tube is
Mass flow rate of water is
Concept used:
Write the expression for the average velocity of water flows through the pipe.
Here,
Write the expression for the maximum velocity.
Here,
Write the expression for the Reynolds number.
Here,
Write the expression for the pressure gradient.
Here,
Calculation:
Substitute
Substitute
Substitute
Substitute
Conclusion:
Thus, The maximum velocity of water inside the tube is
Want to see more full solutions like this?
Chapter 8 Solutions
Fundamentals of Heat and Mass Transfer
Additional Engineering Textbook Solutions
Applied Statics and Strength of Materials (6th Edition)
Fox and McDonald's Introduction to Fluid Mechanics
Manufacturing Engineering & Technology
Heating Ventilating and Air Conditioning: Analysis and Design
Introduction To Finite Element Analysis And Design
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
- 6.1 Determine the heat transfer coefficient at the stagnation point and the average value of the heat transfer coefficient for a single 5-cm-OD, 60-cm-long tube in cross-flow. The temperature of the tube surface is , the velocity of the fluid flowing perpendicular to the tube axis is 6 m/s, and the temperature of the fluid is . Consider the following fluids: (a) air, (b) hydrogen, and (c) water.arrow_forward- EXAMPLE 8-1 Laminar Flow in Horizontal and Inclined Pipes Consider the fully developed flow of glycerin at 40°C through a 70-m-long, 4-cm-diameter, horizontal, circular pipe. If the flow velocity at the centerline is measured to be 6 m/s, determine the velocity profile and the pressure dif- ference across this 70-m-long section of the pipe, and the useful pumping power required to maintain this flow. For the same useful pumping power input, determine the percent increase of the flow rate if the pipe is inclined 15° downward and the percent decrease if it is inclined 15° upward. The pump is located outside this pipe section. D-2 em 6 m/s Glycerine Hello sir, I want the same solution, but in a simplified way without the words of simplifying the solution. ur) - uma 1- Substituting, the velocity profile is determined to be ur) - (6 m/s)I - - 6(1 - 2500r) (0.02 m) where u is in m/s and r is in m. The average velocity, the flow rate, and the Reynolds number are V - Vavs 4max 6 m/s - 3 m/s…arrow_forwardWhat is the Reynolds number of a fluid flowing in a tube with an inside diameter of 2 inches? The viscocity is 1.358 x 10^-5 lb/ft-s and the mass flow rate is 73 lb/h.arrow_forward
- Water at 27°C flows with a mean velocity of 1 m/s through a 1 km-long pipe of 0.25 m inside diameter. Answer the following: a. Is the flow hydrodynamically fully developed? Support your answer with calculations. b. Is the flow thermally fully developed? Support your answer with calculations. c. What is the pressure drop over the pipe length, if the pipe surface is smooth? (Ans: 0.289 Bar) d. What is the pump power requirement, if the pipe surface is smooth? (Ans: 1.42 kW)arrow_forwardHelium at 25°C and 110 kPa (absolute) flows into a copper tube (1-1/4-standard, type M) that is 10 m long. Is the flow fully developed at tube end if the helium mass flow rate is 0.02 kg/s? Ethyl alcohol flows into a 6 cm ID pipe through a well-rounded entrance. After 20 cm of pipe length, measurements taken in the pipe show that the flow is fully developed. Determine the volume flow rate in the pipe, assuming laminar flow exists.arrow_forwardWater at 15°C is flowing through a 10 cm cast iron pipe (ɛ=0.26 mm) at 1 L/s. The friction coefficient O a. Is a function of Reynolds number alone b. Is a function of relative roughness alone O c. Is a function of Reynolds number and relative roughness O d. Is independent of the roughness coefficientarrow_forward
- An electronic device is cooled by water flowing through capillary holes drilled in the casing as shown in below figure. The temperature of the device casing is constant at 353 K. The capillary holes are 0.3 m long and 2.54x10-3 m in diameter. If water enters at a temperature of 333 K and flows at a velocity of 0.2 m/s, calculate the outlet temperature of the water. 0.3 m 0000000000 Surface Water 333 K 0.2 m/s 2.54 x 10m temperature = 353 K Water Capillary holes Single capillaryarrow_forward1. Experimental analysis was carried out about turbulent convective heat transfer in trapezoidal cross-sectioned duct.Average Nusselt numbers and Reynolds numbers were determined for each experiment and the following data set have beenobtained from this investigation. Find an engineering correlation between the average Nusselt number and Reynolds numberin the form ofNu = aRebarrow_forwardA 2-cm diameter, 10-m long tube transports water at an average flow velocity of 8 m/s. The water enters at 20°C and leaves at 30°C. To compute for the Nusselt number of the water flow, what is the exact value of the temperature in °C on which the water properties should be based?arrow_forward
- FLUID DYNAMICS Discuss the factors that influence pressure drop due to friction both for laminar flow and for turbulentflow in fluid flow in pipes.arrow_forwardWater at 10oC enters a tube of 0.1 m diameter at the mean flow velocity of 0.4 kg/s. Calculate the exit water temperature if the tube is 15 m long and the wall temperature is constant 30oC.arrow_forwardA 10 m long thin-walled stainless steel tube of diameter 15 mm is used to sterilize pharmaceutical products by heating it from 25 °C to 85 °C. A uniform heat flux is maintained on the outer surface of the tube by an electric resistance heater wrapped around it. If the flow rate of the liquid is 0.15 m/s, find the required heat flux. Is the flow in the tube laminar or turbulent? Assuming the fluid exits the tube with a fully developed velocity and temperature profile, determine the tube surface temperature at the exit. Explain the reasoning for assuming that the flow is fully developed.arrow_forward
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning