Applied Statics and Strength of Materials (6th Edition)
6th Edition
ISBN: 9780133840544
Author: George F. Limbrunner, Craig D'Allaird, Leonard Spiegel
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 9, Problem 9.36SP
Consider the bolted lap joint shown in Figure 9.12. Assume that the joint consists of two steel plates connected by two 25-mm-diameter bolts and that the load is equally resisted by the two bolts. Calculate the average shear stress in the bolts when the joint is subjected to a tensile load of 120 kN.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Design a single riveted lap joint to connect two mild steel plates, 14.5 mm thick, the joint being designed for maximum efficiency. The allowable stresses are σt = 55 N/mm2 , = 32.5 N/mm2 and σc = 63.5 N/mm2 . Also calculate the minimum force per pitch which will rupture the joint
Two plates 50 mm wide and 20 mm thick are lap jointed by a 20-mm dia. pin and loaded with 75 kN tensile force. Estimate shear stress on the pin in MPa.
A member in tension in a machine frame is subjected to a continuous load of 5.00 kN. Its length is 750 mm and it is made of a carbon steel tube with an outer diameter of 17 mm and an inner diameter of 12 mm. Calculate the tensile stress (in MPa).
Chapter 9 Solutions
Applied Statics and Strength of Materials (6th Edition)
Ch. 9 - Write the direct stress formula in its three forms...Ch. 9 - A 6-in-diameter concrete test cylinder is loaded...Ch. 9 - Determine the tensile stress in each segment of...Ch. 9 - Calculate the stress developed in the following...Ch. 9 - The following members are subjected to axial...Ch. 9 - Determine the stresses in the two segments of the...Ch. 9 - A bin weighing 8 tons is supported by three steel...Ch. 9 - Diameters of small commercially available steel...Ch. 9 - A No. 32 (metric designation) reinforcing bar for...Ch. 9 - In the bolted connection of Figure 9.12 , assume...
Ch. 9 - Compute the force required to punch a...Ch. 9 - The 34 — in. — diameter bolt shown is subjected to...Ch. 9 - Why is strain unitless (or dimensionless)?Ch. 9 - (a) Given =1.2in. and L=100ft calculate (b) Given...Ch. 9 - A short compression member 2 in. by 2 in. in cross...Ch. 9 - A 100-ft-long rod is suspended from one end. The...Ch. 9 - Compute the total elongation of a steel bar,...Ch. 9 - A steel rod 34 in. in diameter and 25 ft long is...Ch. 9 - An aluminum rod 25mm in diameter and 4m long is...Ch. 9 - A steel rod 10 ft long is made up of two 5 ft...Ch. 9 - A titanium alloy bar elongates 0.500 in. when...Ch. 9 - Write a program that will calculate the allowable...Ch. 9 - Write a program that will compute stress, strain,...Ch. 9 - The Viking Bin Company manufactures suspended bins...Ch. 9 - Write a computer program that will calculate the...Ch. 9 - The joint between a diagonal and a chord in a...Ch. 9 - In Problem 9.26, find the required length of the...Ch. 9 - A column is supported by a base plate, pedestal,...Ch. 9 - If the soil pressure under the footing of Problem...Ch. 9 - A hopper weighing 75 kN is supported by three...Ch. 9 - A steel bar has a rectangular cross section 25 mm...Ch. 9 - A steel wire is suspended vertically from its...Ch. 9 - A W1240 shape is subjected to a tensile load of...Ch. 9 - Calculate the required diameter of steel tie rods...Ch. 9 - A 30-ft-long steel rod of circular cross section...Ch. 9 - Consider the bolted lap joint shown in Figure...Ch. 9 - An inclined member is braced with a glued block,...Ch. 9 - Calculate the force a punch press must exert if it...Ch. 9 - A 34 - in. - diameter punch is used to punch a...Ch. 9 - A control arm is keyed to a 1-in. -diameter shaft...Ch. 9 - Calculate the required width b for the key of...Ch. 9 - A 25-mm-diameter aluminum rod, 3 m long, is...Ch. 9 - A short timber post of Douglas fir is subjected to...Ch. 9 - A 1 00-ft surveyor’s steel tape with a...Ch. 9 - An 18-in-long steel rod is subjected to a tensile...Ch. 9 - Compute the magnitude of the tensile load that...Ch. 9 - A 5-mm-diameter steel wire, 18 m in length, is...Ch. 9 - A structural steel rod 112 in. in diameter and 20...Ch. 9 - A rectangular structural steel eyebar 34 in. thick...Ch. 9 - 9.50 A
in. — diameter steel rod, 100 ft long, is...Ch. 9 - For the truss shown, compute the total deformation...Ch. 9 - A steel bar with a cross section of 12 in. by 12...Ch. 9 - Rework Problem 9.52 , changing the second load...Ch. 9 - In the structure shown, the tie-back BC is a round...Ch. 9 - A hook is suspended by two steel wires, as shown....Ch. 9 - The trolley of a small hoist is supported on a...Ch. 9 - The steel piston rod to the master cylinder has a...Ch. 9 - A stranded steel brake cable is composed of 7...Ch. 9 - The piston of a steam engine is 400 mm in diameter...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A plate 100 mm wide and 10 mm thick is to be welded with another plate by means of transverse welds at the ends. If the plates are subjected to a load of 70 kN, find the size of weld for static load The permissible tensile stress should not exceed 70 MPa.arrow_forwardA bracket, as shown in Fig below, carries a load of 40 kN. Calculate the size of weld, if the allowable shear stress is not to exceed 80 MPa. All dimensions in mm.arrow_forwardThe central plates a in Fig.12 of the text are 9/16 in. thick and 9 in. wide. The diameter of the rivets connecting these plates to the outside plates is 1 in. If the allowable unit stress in tension on the net area is 20,000 psi, the safe tensile strength of eith central plate is A. 90,000 lb B. 88,600 lb C. 78,600 lb D. 75,800 lbarrow_forward
- A plate 100 mm wide and 12.5 mm thick is to be welded to another plate by means of parallel fillet welds. The plates are subjected to a load of 50 kN. Find the length of the weld so that the maximum stress does not exceed 56 MPa. Consider the joint first under static loading and then under fatigue loading.arrow_forwardWhat wall thickness in mm is required for a 634 mm diameter cylinder under an internal pressure of 18 MPa? Use a design stress of 80 MPa?arrow_forwardWhat will be the minimum diameter of a steel wire, which is used to raise a load of 4000N if the stress in the rod is not to exceed 95 MN/m²?arrow_forward
- A steel rod of length 10 m is subjected to a axial load of 10 kN. Calculate the elongation of the rod when its diameter is 40 mm.arrow_forwardQuestion: a) A plate 100 mm wide and 10 mm thick is to be welded to another plate by means of double parallel fillets. The plates are subjected to a static load of 80 kN. Find the length of weld if the permissible shear stress in the weld does not exceed 55MPa. Determine the increase in load carrying capacity if a combination of single transverse double parallel fillet is used the permissible tensile strength of material is 80MPa. b) Draw a neat sketch of double riveted double cover but joint. If 8mm plates with 20 mm diameter rivets having a pitch of 50 mm are joint using double riveted lap joint. The permissible stresses are permissible tensile stress = 120 MPa;Permissible crushing stress= 100 MPa; Permissble shear stess= 150 MPa. Find the strengths and efficiency of joint, taking the strength of the rivet in double shear acoording to the indian boiler standards.arrow_forwardA circular shaft of diameter 120 mm is welded to a rigid plate by a fillet weld of size 6 mm. If a torque of 8 kNm is applied to the shaft, what is the maximum stress in the weld?.arrow_forward
- A cylindrical pressure vessel, mean radius 15 in, is filled with a gas of molecular weight causing an internal pressure of 3500 psi. The efficiency of welded connection in the vessel is 78%. Assuming the material of the vessel to have a yield strength of 12 x 10⁴ psi, calculate for this strength the thickness of the vessel assuming a factor of safety of 1.5. draw diagramarrow_forwardA light standard for a highway is shown in figure 6.52. Although it is made entirely of welded aluminum, the member ABC is presumed to be continuous and pin connected at B and C. According to this conservative assumption, what is the tension force in the strut at B? Neglect the weight of the aluminum members.arrow_forwardA cylindrical metal rod of 20mm diameter and 1m length is subjected to a tensile load of 60KN. To what length the cylinder should be centrally bored on one side to reduce weight by material removal, so that the total extension will increase by 10 percent under the same pull. The diameter of the hole being bored on one side is equal to 10mm. Take E= 200GPa.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Differences between Temporary Joining and Permanent Joining.; Author: Academic Gain Tutorials;https://www.youtube.com/watch?v=PTr8QZhgXyg;License: Standard Youtube License