The heat loss (Q/t, in units of joules per second [J/s]) from the surface of a hot liquid is given by:
Choose the correct set of fundamental dimensions for the parameter (h) from the choices below if the area (A) is given in units of square meters [m2]. Both the temperature of the liquid (T) and the ambient temperature (T0) are measured in degrees Celsius [°C].
- A. MT–3
- B. MT–3Θ–1
- C. ML2T–1Θ
- D. L2T–1
Want to see the full answer?
Check out a sample textbook solutionChapter 9 Solutions
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
Additional Engineering Textbook Solutions
Mechanics of Materials
Fundamentals of Heat and Mass Transfer
Vector Mechanics for Engineers: Statics and Dynamics
Engineering Mechanics: Dynamics (14th Edition)
Engineering Mechanics: Statics
Vector Mechanics for Engineers: Statics, 11th Edition
- 1.1 s) The overall size of the system (i.e. the shell) is 5.8 inch ID and a 27-inch long tube section. Assuming tubes are 1/2 inch in diameter (ignore thickness) and that the tubes are spaced with 1/4 inch between them. Estimate the number of tubes that will fit in the shell. O 36 O 60 O 13 O 46 QUESTION 2 1.22 area [ft²]. Og ft² 5 ft² O 17.66 ft2 10.6 ft2 Regardless of your answer to part 1.1, use 36 as the number of tubes and estimate the total heat transferarrow_forwardThe following processes occurs in a reversible thermodynamic cycle: 1-2: Reversible polytropic compression at pressure [X] bar at volume [Y] m3 to a pressure [Z] bar and specific volume [A] m3/kg. The index of compression may be taken as n. 2-3: Reversibly expansion with expansion index of 2 to pressure [B] bar. 3-1: Reversible cooling at constant volume to the initial state. What are the final attempt values of X, Y, Z, A and B from the Part A of the eThuto Assessment. calculated formula similar question? X= ; Y= ; Z= ; A= ; B=arrow_forwardA heat generating slab with thermal conductivity of k [W/m-K] and heat generation rate d" [W/m³] is perfectly insulated on the left side (x = 0) . h1 and is exposed to air with ambient temperature T1 [K] and convection coefficient of hi [W/m²-K] on the right as shown in Fig. 1. Neglect Air Slab radiation. Find out the temperature distribution (i.e., temperature as X= () a function of x) within the slab in terms of the variables shown in the Figure 1: Note the figure. indicated positive direction for reference. SPerfect Insulationarrow_forward
- Ql: The viscosity in industrial measurement continue to use the CGS system of Lunits, since centimeters and grams vield convenient numbers for many fluids. The absolute viscosity () unit is the poise, I poise = 1 gtem. s). The kinematic viscosity (v) unit is the stohes, I stokes = 1 em /s. Water at 20C has u = 001 poise and also V= 0.01 stokes. Express these resalts in (a) SI and (h) BG tanits.arrow_forward|The following processes occurs in a rever sible thermodynamic cycle: 1-2: Reversible polytropic compression at pressure X)bar at volume Y)m' to a pressure [Z]bar and specific volume (A]m'/kg. The index of compression may be taken as n. 2-3: Reversibly expansion with expansion index of 2 to pressure [B/bar. 3-1: Reversible cooling at constant volume to the initial state.arrow_forwardAir A Water Calculate the gauge pressure, in kPa, at A, B, C, D in the reservoirs shown above. (Note that the reservoirs between A and B are connected.) Problem parameters: h1 = 1.1 [m] h2 = 0.3 [m] h3 = 0.4 [m] h4 = 0.5 [m] Density of water is 1000 [kg/m³]; Density of air is 1.225 [kg/m³]; g = 9.81 [m/s²] S.G. of oil is 0.89 h4 [m] h3 [m] h2 [m] Air B h1 [m] Oilarrow_forward
- The Antoine Equation can be used to estimate vapor pressure at various temperatures for different substances using sets of empirically-derived constants. The equation can be written as: Where for water A = 8.07131, B = 1730.63, C = 233.426, T = temperature [°C], and P = vapor pressure [mmHg]. Note that with these constants the temperature and pressure must be provided in °C and mmHg, respectively. Using the Antoine Equation and the provided constants, what atmospheric pressure (provided in terms of % of standard atmospheric pressure) will permit water to boil at 75 °C?arrow_forward4:17 .l 86% google.com Water flows from point A to points D and E as shown. Some of the flow parameters are known, as shown in the table below. Determine the unknown parameters. Q1 V1 Q2 V2 D2 Qa V3 D3 D D: Q4 V4 A в D4 E Section Diameter [mm] | Flow rate [m³/s] Velocity [m/s] |AB BC 350 222 ??? 2?? Q3=2Q4 |Q«=0.5Q. 750 1.5 ??? 150 1.7 ??? CD СЕ C Chegg Visit Solved: Water Flows From Point A To Points D And E As Show ... Images may be subject to copyright. Learn more Related images O V tees f p A p Dd p E e ies ef pie de Gm t eeesnde pe the e be ple the er de e N d k hee may etheme4 Water fows fhem peint Ato pos Dand E as shon Sone of the flow parancters are knon, ashown in the able below Drenine he ukow paranem Sertan Dia r Phee rate Veleci jas LAB BC elect ja w y 150 ate K lo H- | Solved: Q3) Water Flows From Poi. chegg.com Solved: Quiz 2 Water Flows From P... TOTAL chegg.com Water flows theoagh a 150 m diameter horintal pipe at the steady ma flow rate of 60kg/s A meticn i fitted…arrow_forwardTo understand the heat transfer from a bar in cross flow, you conduct a series of experiments measuring the average heat transfer coefficient as a function of the free stream velocity. A schematic of the experiment and the accompanying results are shown below. L = 0.3 m h [W/m²-K] 60 40 V [m/s] 20 15 a) You expect the important dimensionless parameters to be related by a function of the form Nu = CRe Pr where C, m, and n are constants. The film temperature in both the experiments is approximately the same. Use the given experimental results to determine the constant m b) Calculate h for L = 0.75 m and V = 30 m/s.arrow_forward
- In the process of cutting a metal piece to obtained chips, a cutting force of 100 N, a tangential force of 120 N, and a rake angle of 250 are applied. Use a scale and protractor, to measure off distances (forces) [R-resultant force, F-friction force and N-normal force], and friction angle.arrow_forwardA 2 cm thick steel pipe (thermal conductivity 43 W/[m °C]) with 6 cm inside diameter is being used to convey steam from a boiler to process equipment for a distance of 40 m. The inside pipe surface temperature is 115°C, and the outside pipe surface temperature is 90°C. If there is 600kW of heat loss, what is the thickness of the pipe?arrow_forwardYou are heating motor oil to make it flow better from the original shipping container to the new container you built. You know that the heating rate of the motor oil is 2.50 degrees Celsius per slug second [°C /(slug s)]. Express this heating rate in units of degrees Fahrenheit per pound-mass second [°F/ (lbm s)]. Click the icon to view the conversion table. Click the icon to view the factors for temperature intervals conversion The heating rate is °F / (lbm s). (Round your answer to three decimal places.)arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY