Joseph is painting a right triangular section of the ship with the longest side of 12 meters and the other shorter side of 6 meters. How large is the section

Q: Determine the minimum height exceed 20 MPa. I= bh²³ € 12 my J 2.5 kN/m Rislo m 8.5 1m of the beam…

A: Given: σmax=20Mpa b = 80mm

Q: Consider the shaded area in (Figure 1). Take a = 460 mm. Figure 150 mm 150 mm 100 mm 300 mm 1 of 1…

A:

Q: Longerons are used to oppose? a. Bending b. Tension C. d. Drag Compression

A: Longerons are members of aircraft structures.

Q: An iceberg has mass 128,000 tonnes (1 tonne = 1000 kg) and is composed of pure ice with density 917…

A: Given data: Mass of the ice (mi) = 128000 tonnes = (128000×1000) kg = 128,000,000 kg The given…

Q: Block C starts from rest and moves downward with a constant acceleration. Knowing that after 10 s…

A:

Q: 2. A velocity field is given as U= = 3xy + t²,v=y+t² and w=1-zt² Determine local, convective and…

A: Acceleration is defined as the rate of change of velocity with respect to time.…

Q: Two identical centrifugal pumps connected in series are used to pump water between two storage tanks…

A: Inner diameter of pipe, d=0.1 mTotal Equivalent length on the suction side, Ls=20 mTotal Equivalent…

Q: Helium gasi

A: h10.303 MPa,275 K=1444kJ/kgs10.303 MPa,275 K=28.7kJ/kgKh24.04 MPa,300 K=1586kJ/kgs24.04 MPa,300…

Q: Question 6 of 10 In the figure, block 1 has mass m₁ = 460 g, block 2 has mass m₂ = 580 g, and the…

A:

Q: Q4-/A/ During orthogonal cutting operation of material has shear strength 95.5 M The cutting force…

A:

Q: In (Figure 1), take a = 2 m. Figure ay I y 1 of 1> Part A Locate the centroid y of the paraboloid.…

A:

Q: Q1-A/ In a tensile test on a metal specimen, true strain = 0.08 at a stress = 265 MPa. When the true…

A:

Q: QUESTIONS: 1. WHAT KIND OF ERRORS ARE THEY? 2. HOW TO AVOID THESE ERRORS IN MEASUREMENTS?

A: Graph -1: Hysteresis error Graph - 2: Linearity error Graph - 3: Sensitivity error Graph - 4: Zero…

Q: R(s) XIS K s+5 s+2 s+3 Y(s)

A:

Q: 2. In the figure shown, a liquid with specific gravity of 0.85 is pumped from reservoir A to tank B…

A:

Q: The system in the figure is in equilibrium. A concrete block of mass 203 kg hangs from the end of…

A:

Q: Compute the moment (positive if counterclockwise, negative if clockwise) of the 0.36-lb force about…

A:

Q: Use the method of sections to determine the forces in members BD, CD, and CE of the Warren truss…

A:

Q: Find the resultant Force and direction of adding the three vectors shown

A:

Q: 2,1) In a heat exchanger, determine the amount of mass per unit time of refrigerant needed to get…

A:

Q: A particle is moving on a straight line with a velocity v = 25 m/s which is increasing at a rate of…

A:

Q: Q/ The force in the member (CA) is 12m 50 ку. 10 points 5m 16x

A:

Q: 2- Entropy defined as the measure of the of the system. ...... a- Stability b- Order and disorder,…

A: Option d is correct

Q: A 450kN force is needed to punch a 30mm diameter hole in a plate that is 10mm thick. Determine the…

A:

Q: Compare single threaded and multiple threaded screw and state the benefit why it has been…

A: Comparision: Single threaded screw: 1.It has only one continuous thread all over the body.  2.For…

Q: Q/ If F1 = 250 N and F2 = 375 N are two forces, the angle between F1 and the positive y- axis is…

A: The resultant force FR is 393 N. Therefore, option (c) is correct answer.

Q: If feedwater is supplied at 50 degrees Celcius, a boiler generates 10,000 kg/hr of steam at 98%…

A: (a) Write the given data. T1=50 °Cm˙=10000 kg/hrx2=0.98P2=1 MPa

Q: A tensile test uses a test specimen that has a gage length of 50 mm and an area = 200 mm². During…

A:

Q: The slender bar of mass moe-22 kg is moving to the right on frictionless rollers at A and B with the…

A: Given Data The mass of the bar is: mbar=22 kg The length of the bar is: L=3 m The angle of the bar…

Q: 2. In an aircraft refrigeration as shown in the figure below, air bled from the jet engine is at 326…

A: Simple air craft refrigeration system Neglecting ramming effect and considering inlet pressure to…

Q: A box weighing 150lb is moved across a horizontal  Floor by dragging it by means of a rope attached…

A: Whenever the surfaces of two bodies are in contact there will be limited amount of resistance to…

Q: 1.15 Considering the stress state represented in Figure Q1.15, the maximum shear stress: in 3D y=G…

A: Given question: Considering the stress state represented in Figure, the maximum shear stress in…

Q: Q.4) The rod is supported by journal bearings at A, B and C and subjected to a force of 500 N (in…

A: Given: The force, F = 500 N The moment, M = 400 N.m

Q: 4. Riser (a) What is the pur

A: A reservoir build up into a metal casting mold so as to prevent the cavities because of shrinkages…

Q: mounting chart: Select one: a. describes the dimensions and finish of each component. b. shows an…

A: we will discuss the function of a mounting chart

Q: During a steady right turn, a person exerts the forces shown on the steering wheel. Note that each…

A: The moment exerted about the steering column at O: M = -1.8014 N•m ... (Clockwise)

Q: A vacuum of 42 kPa is measured in an airflow at sea level where the ambient pressure is 101.3 kPa.…

A:

Q: Question 1.9 A beam is constructed of a channel section. The cross section has the dimensions…

A: Q1.9 Given: The moment of inertia, I = 1.2x10^6 mm^4 The moment about z-axis, M = -1 kN.m = -1000…

Q: Q3- B/A round disk of 150 mm diameter is to be blanked from a strip of 3.2 mm half hard cold-rolled…

A:

Q: Calculate the height of capillary rise in a glass capillary tube having a radius of 3.5 x10-5 m. The…

A: Given data : Surface tension σ=72.7 mN/m Radius R=3.5×10-5 m Acceleration due to gravity g=9.81 m/s2…

Q: 1- The fluid with constant density is called an: a. Ideal fluid b. compressible fluid c.…

A: Given the fluid with constant density

Q: Q4-/A/ During orthogonal cutting operation of material has shear strength 95.5 Mpa. The cutting…

A:

Q: The beam shown in Fig. is made from two boards. Draw the shear stress at (A.B.C.D) to hold the…

A: Given   Load, P = 6.5 kN/m Length, L = 8 m Find   Shear stress diagram

Q: n Question 1.2 A material has a modulus of elasticity E and a shear modulus of 0.4x E. The Poisson's…

A: Given data: Elasticity=EG=0.4E Need to determine the poison's ratio of the material.

Q: Question 1.20 The yield stress of a material is 45 MPa. This material is subjected to the maximum…

A: Yield stress of material = σy=45 MPa Maximum normal stress in material = σ1 Minimum normal stress in…

Q: The state of strain at the point on the pin leaf has components of € = 200(10-6), y = 180(10-6), and…

A: Introduction: When an elastic body is subjected to external forces, material locations inside the…

Q: A circular shaft has a second polar moment of area of 7.3 x 107 m and a length 2.3 m. The shear…

A:

Q: The system in the figure is in equilibrium. A concrete block of mass 215 kg hangs from the end of…

A: Given data as per the question Mass of block =215 kg Mass of strut =41.4 kg

Q: 3.1) A plunger-cylinder that initially contains 0.55 kg of air at a temperature of 250 °C and a…

A:

Q: Q/ Compute the pull force (F) on the rope exerted by the man to hold the crate in the position…

A: