Concept explainers
(a)
Write the equations for shear force and bending moments based on singularity function.
(a)
Answer to Problem 110P
The equation of shear force as a singularity function is;
The equation of bending moment as a singularity function is;
Explanation of Solution
Show the free-body diagram of the beam as in Figure 1.
Determine the vertical reaction at point E by taking moment about point A.
Determine the vertical reaction at point A by resolving the vertical component of forces.
Write the equation of the shear force function as follows;
The equation for bending moment as a function of shear force is,
Integrate the equation (1) to find M;
Therefore,
The equation of shear force as a singularity function is;
The equation of bending moment as a singularity function is;
(b)
The maximum normal stress due to bending using the singularity function.
(b)
Answer to Problem 110P
The maximum normal stress due to bending is
Explanation of Solution
Refer to Equation (2).
Point A
Substitute 0 m for x in Equation (2).
Point B
Substitute 0.75 m for x in Equation (2).
Point C
Substitute 1.5 m for x in Equation (2).
Point E
Substitute 2.25 m for x in Equation (2).
Point E
Substitute 3 m for x in Equation (2).
Point F
Substitute 3.75 m for x in Equation (2).
Refer to the calculated bending moment values, the maximum bending moment occurs at point C.
The maximum bending moment in the beam is
Refer to Appendix C “Properties of Rolled-Steel Sections” in the textbook.
The section modulus (S) for
Determine the maximum normal stress
Substitute
Therefore, the maximum normal stress due to bending is
Want to see more full solutions like this?
Chapter 5 Solutions
Mechanics of Materials, 7th Edition
- (B) Q: The cantilever beam shown below has a circular cross section of 50mm outer diameter. Portion AB of the beam is hollow, with an inner diameter of 35mm. If the allowable bending stress is 140 MPa, determine (1) the largest allowable uniformly distributed load (w) that can be applied to the beam; (2) the bending stress at a point that is 7 mm below the top of the beam at section D. 50 mm W D B O! 35 mm A - 750 mm 250 mmarrow_forwardQ4. An extruded beam has the cross-section shown. Determine (a) the location of the shear centre O, and (b) the distribution of shear stress caused by a 110 kN vertical shear force applied at O. [Ans. e 19.8 mm, member BD: T = 24.23 MPa at B; T = 56.54 MPa at C] 12mm O e B V = 110 kN 6mm ↓ C A 6mm 200mmarrow_forward*5.64 The beam AB supports two concentrated loads P and Q. The normal stress due to bending on the bottom edge of the beam is +55 MPa at D and +37.5 MPa at F. (a) Draw the shear and bending-moment diagrams for the beam. (b) Determine the maxi- mum normal stress due to bending that occurs in the beam. A 0.2 m C m 5 m 0.5 r DE 0.4 m Fig. P5.64 Q F B 00:00 0.3 m 24 mm 60 mmarrow_forward
- A beam carries the loading shown in Fig. 4. Determine, (a) the smallest allowable width b of the beam if the maximum allowable bending stress is 93.75 MN/m². (b) to reduce the weight, a bore was made at the center of the rectangle with a diameter of 60 mm, what is the second moment of area of the resulting shape? 3 m 2 kN/m B www. 9 m Fig. 4 8 kN 3 m D 0000 1 160 mmarrow_forward5.39 The overhanging beam carries a uniformly distributed load totaling 8 W and (Wo concentrated loads of magnitude W each. Determine the maximum safe value of Wif the working stresses are 3000 psi in tension and 10000 psi in compression. W 8W (total) W 7 in. 1 105 in D NA 3 in. 16ft 4 ft FIG. P5.39arrow_forwardSection 5.1 5.1 through 5.11 Determine the axial forces, shears, and bending moments at points A and B of the structure shown. 40 k Hinge A B | | | 10 ft + 5 ft 5 ft FIG. P5.8 10 ft 40 k + 10 ftarrow_forward
- - -.... .. . and 5.8 beam and loading shown, and determine the maximum absolute value (a) of the shear, (b) of the bending moment. Draw the shear and bending-moment diagrams for the 200 N 200 N 500 N 200 N A C D' E 300 225 300 225 Dimensions in mm Fig. P5.8arrow_forward5.16 The box beam is made by nailing four 2-in. by 8-in. planks together as shown. (a) Show that the moment of inertia of the cross-sectional area about the neutral axis is 981.3 in.. (b) Given that wo 300 lb/ft, find the largest allowable force P if the bending stress is limited to 1400 psi. 8 in.2 in. 8 in. 9 f 3 ft 2 in. FIG. P5.16arrow_forwardDraw the shear and bending-moment diagrams for the beam and loading shown and determine the maximum normal stress due to bending. | 25 kips | 25 kips | 25 kips E A B S12 × 35 6 ft 1 ft 2 ft 2 ft Fig. P5.21arrow_forward
- Q1. For the beam and loading shown, (a) draw the shear and bending- moment diagrams, (b) determine the equations of the shear and bending-moment curves. 20 kN/m А 3 m 12 m Q2. A steel bar of rectangular cross section is subjected to two equal and opposite counles acting in the vertical plane of symmetry of the bar. Determinearrow_forward(14) A beam of I-section is 2 in. wide and 4 in. deep with all sections 1/2 in. thick. It is supported at points 5ft. apart, and carries a concentrated load of 400 lb at a distance of 2ft from the left support. (a) Determine the horizontal shear in the vertical section just to the left of the load and at distances of 0, 1, and 2 in. from the neutral axis. (b) Determine the horizontal shear in the vertical section just to the right of the left support and at distances 0, 1, and 1 ½ in. from the neutral axis.arrow_forwardPROBLEM 5.21 For the beam and loading shown, determine the maximum bending stress on a transverse section at C. [Ans. 10.89 MPa] 10 kN 3 kN/m 100 mm 25 de 200 mm B 1.5 m 1.5 m X-X 2.2 m splay E23 Fig. P5.21 Chp Show all 205 14 04/22 ALING • SPARKLING PURDEY'S NATURAL ENERGT REFOCUS Dark Fruits with guarana Paune hp Prien Sem Sysha Scroll Serril Lock F11 F10 F9 Num Lock F8 Page Up F7 F6 Home F5 bert F4 7 Page Down Home End Deletearrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY