Consider the tube and inlet conditions of Problem 1.36.Heat transfer at a rate of
Want to see the full answer?
Check out a sample textbook solutionChapter 1 Solutions
Fundamentals of Heat and Mass Transfer
Additional Engineering Textbook Solutions
Degarmo's Materials And Processes In Manufacturing
Engineering Mechanics: Dynamics (14th Edition)
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
Introduction to Heat Transfer
Engineering Mechanics: Statics & Dynamics (14th Edition)
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
- For an inlet valve, the mass flow rate through the valve is 0.44 kg/s. The flow coefficient is 0.62 and the cylinder pressure is 105 kPa. Assume intake system pressure and temperature are 180 kPa and 527 K, the specific heat ratio is 1.3 and R =287 J / kg.K. The area of the valve is (SI unit): Select one: a. 2.30*10-3 O b. 3.45*10-2 O c. 1.43*10-3 O d. 1.75*10-3 O e. 0.85*10-2arrow_forwardYou are provided a horizontal tube with one entrance and one exit. Air (Cp = 1.005 kJ/(kg-K)) is passing through the pipe and is assumed ideal. The inlet conditions are 102 psia, 101 degrees Fahrenheit and velocity 9 feet/second. Determine the outlet velocity (ft/s) and outlet temperature (degrees Fahrenheit) if the exit conditions are 2.1 psia. Assume the process occurs under adiabatic conditions. Write all the assumptions you made in solving the problem.arrow_forwardWater is pumped up to 8 m height. The pump operates in steady state, and it is perfectly insulated. Pressure increase over the pump is 850 kPa. The velocity of the water at the pump inlet w is 1 m/s and at the outlet w₂7 m/s. The diameter of the inlet d' is 0.12 m. The water is saturated at the inlet, and the temperature Tis 18 °C. The density of the water is assumed to be constant. The efficiency of the pump n is 77.0 %. Reduce the equation for energy balance with the given assumptions, and calculate the power of the pump and the fraction of kinetic energy. 0 = P + + qmh₂ h₁ + Read from h,s-chart Specific volume of inlet water v Power of pump P 2 w² - w² 2 The share of kinetic energy of the total pump power -2₁)) + g(²₂ — Z₁)arrow_forward
- A nozzle is a device for increasing the velocity of a steadily flowing stream of fluid. At the inlet to a certain nozzle the enthalpy of the fluid is 3025 kJ/kg and the velocity is 60 m/s. At the exit from the nozzle the enthalpy is 2790 kJ/kg. The nozzle is horizontal and there is negligible heat loss from it. (i) Find the velocity at the nozzle exit. (ii) If the inlet area is 0.1 m2 and specific volume at inlet is 0.19 m3/kg, find the rate of flow of fluid (iii) If the specific volume at the nozzle exit is 0.5 m3/kg, find the exit area of the nozzle.arrow_forwardQ2/A condenser has vacuum of 70 cm of Hg when barometer reading is 76 cm. Condenser has temperature of 30°C. Air leaks into condenser at the rate of 1 kg air per 2500 kg steam. Calculate (i) the capacity of air pump per kg of steam for removal of air from steam entering condenser, and (ii) the mass of water vapour accompanying this air.arrow_forward(b) Hairdryer is an electromechanical device that blows ambient or hot air over damp hair to speed the evaporation of water to dry the hair. To design a hairdryer, it should contain the following basic components: a duct of constant diameter with a few layers of electric coils, a small fan to pull the air in and force it through the heating coils. If the density of air is 1.18 kg/m³ at the inlet and 0.90 kg/m³ at the exit, calculate the percent increase in the velocity of air as it flows through the dryer.arrow_forward
- Your second customer wants to determine the required electrical power, which will be used to pump waterwith the following design specifications: The pump loses 3 kW in the form of heat to its surrounding. The inlet and the exit conditions of the water are as indicated in Figure 2. The pipe diameter is 5 cm.arrow_forwardWater at 33 °C flows in a straight horizontal pipe in which there is no exchange of either heat or work with the surroundings. Its velocity is 9 m/s in a pipe with an internal diameter of 1.5 inch until it flows into a section where the pipe diameter abruptly increases. What is the temperature change of the water if the downstream diameter is 2 inches?arrow_forwardApply the first law of thermodynamics to flow system with two inlets and one outlet. Assume that heat is supplied to the system. Draw the neat sketch and lable inlet and outlet propertiesarrow_forward
- During the experiment at time 1:40 min, manometer reading is 5 bar and power consumption at ammeter is 3.3 A. Calculate the work done at that particular time and outlet temperature. Ambient condition: 1 bar and 20 °C Equation for the work done, i.e. output work: n n-1 RT. (S W12 = n- 1 n-1 P. T, = T, Given: Polytropic coefficient: n = 1.3 Ideal gas constant: R = 287 kg K %3D kg Density of air at 20°C: p = 1.2041 Volume flow rate: V = 115 L min Motor Voltage: 230 V at 50 Hz What is the inlet temperature in K and the inlet pressure in bar? What is the outlet temperature at time 1:40 min? At time 1:40 min, how much work is done by the piston? What is the input power at time 1.40 min?arrow_forwardWith a 50 m^3 capacity, a tank contains steam at 400 degrees Celsius and 4500 kPa. From the tank, steam is vented through a relief valve to the atmosphere until the pressure in the tank falls to 3500 kPa. Assuming the venting process is adiabatic, estimate the steam's final temperature in the tank and the mass of steam vented. (Please help me understand the trial and error part for determining the required amounts by solving.)arrow_forwardDetermine the electrical power supplied to a boiler when the temperature of the entering water is 20 C and the exiting temperature is 89 C. The flow of.the pressured water is 2 Kg/s. There is a negligible pressure drop through this boiler and it operates at a constant pressure of 3 bars. The specific heat is c = 4,370 J/(Kg K). There is a 150W rate of heat loss from the boiler during this process to a surrounding at 293.2 k. Consider steady state conditions.Calculate the total rate of entropy production inarrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY