An aluminum plate 4 mm thick is mounted in a horizontal position, and its bottom surface ¡s well insulated. A special, thin coating is applied to the top surface such that it absorbs 80% of any incident solar radiation, while having an emissivity of 0.25. The density
(a) Consider conditions for which the plate ¡s at a temperature of 25°C and its top surface is suddenly exposed to ambient air at
(b) What will be the equilibrium temperature of the plate when steady-state conditions are reached?
(c) The surface radiative properties depend on the specific nature of the applied coating. Compute and plot the steady-state temperature as a function of the emissivity for
Want to see the full answer?
Check out a sample textbook solutionChapter 1 Solutions
Fundamentals of Heat and Mass Transfer
- 1.11 Calculate the heat loss through a glass window 7-mm thick if the inner surface temperature is 20°C and the outer surface temperature is 17°C. Comment on the possible effect of radiation on your answer.arrow_forwardDetermine the power requirement of a soldering iron in which the tip is maintained at 400C. The tip is a cylinder 3 mm in diameter and 10 mm long. The surrounding air temperature is 20C, and the average convection heat transfer coefficient over the tip is 20W/m2K. The tip is highly polished initially, giving it a very low emittance.arrow_forward1.76 Explain a fundamental characteristic that differentiates conduction from convection and radiation.arrow_forward
- A spherical communications satellite, 2 m in diameter, is placed in orbit around the earth. The satellite generates 1000 W of internal power from a small nuclear generator. If the surface of the satellite has an emittance of 0.3, and is shaded from solar radiation by the earth, estimate its surface temperature.arrow_forwardA horizontal, 3-mm-thick flat-copper plate, 1-m long and 0.5-m wide, is exposed in air at 27C to radiation from the sun. If the total rate of solar radiation absorbed is 300 W and the combined radiation and convection heat transfer coefficients on the upper and lower surfaces are 20 and 15W/m2K, respectively, determine the equilibrium temperature of the plate.arrow_forward1.25 A spherical vessel, 0.3 m in diameter, is located in a large room whose walls are at 27°C (see sketch). If the vessel is used to store liquid oxygen at –183°C and both the surface of the storage vessel and the walls of the room are black, calculate the rate of heat transfer by radiation to the liquid oxygen in watts and in Btu/h.arrow_forward
- 1.1 On a cold winter day, the outer surface of a 0.2-m-thick concrete wall of a warehouse is exposed to temperature of –5°C, while the inner surface is kept at 20°C. The thermal conductivity of the concrete is 1.2 W/m K. Determine the heat loss through the wall, which is 10-m long and 3-m high. Problem 1.1arrow_forward8.15 A mercury bath at is to be heated by immersing cylindrical electric heating rods, each 20 cm tall and 2 cm in diameter. Calculate the maximum electric power rating of a typical rod if its maximum surface temperature is .arrow_forwardThree thin sheets of polished aluminum are placed parallel to each other so that the distance between them is very small compared to the size of the sheets. If one of the outer sheets is at 280C and the other outer sheet is at 60C, calculate the temperature of the intermediate sheet and the net rate of heat flow by radiation. Convection can be ignored.arrow_forward
- A horizontal steam pipe with an outside diameter of 60.0 mm passes through a large room whose walls are at a temperature of 298 K. The outer surface of the pipe wall has a surface temperature of 443 K and an emissivity of 0.8. The air temperature in the room is 303 K. Calculate the rate of heat loss per unit length of the pipe by radiation and natural convection.arrow_forward(a) Calculate the rate of heat transfer by radiation from a car radiator at 110°C into a 50.0ºC environment, if the radiator has an emissivity of 0.750 and a 1.20-m^2 surface area. (b) Is this a significant fraction of the heat transfer by an automobile engine? To answer this, assume a horsepower of 200hp (1.5kW) and the efficiency of automobile engines as 25%.arrow_forwardA 30-m-long hot rod (Diameter = 100-mm) is placed inside a room whose walls and air are at 25 C. The surface temperature of the rod is 150 C. h=10 W/m K. The surface emissivity is: your student number/10. What is the rate of heat loss from the rod? student number =201810372 %3Darrow_forward
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning