Fundamentals of Heat and Mass Transfer
7th Edition
ISBN: 9780470501979
Author: Frank P. Incropera, David P. DeWitt, Theodore L. Bergman, Adrienne S. Lavine
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 1, Problem 1.46P
A blood warmer is to be used during the transfusion ofblood to a patient. This device is to heat blood takenfrom the blood bank at 10°C to 37°C at a how rate of200 ml/mm. The blood passes through tubing of length2 m, with a rectangular cross section
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
In the final stages of production, a pharmaceuticalis sterilized by heating it from 30°C to 75°C as it moves at0.2 m/s through a straight thin-walled stainless steeltube of 12.7-mm diameter. A uniform heat flux is maintained by an electric resistance heater wrappedaround the outer surface of the tube. If the tube is 10 m long, what is the required heat flux? If fluidenters the tube with a fully developed velocity profile and a uniform temperature profile, what is thesurface temperature at the tube exit? Fluid properties may be approximated as ? = 1000 kg/m3, cp =4000 J/kg K, ? = 2 x 10-3 kg/s m, k = 0.8 W/m K, and Pr = 10.
8.21 WP In the final stages of production, a pharmaceutical is sterilized by heating it from 25 to 75°C as it moves at o.2 m/s through a straight thin-
walled stainless steel tube of 12.7-mm diameter. A uniform heat flux is maintained by an electric resistance heater wrapped around the outer surface
of the tube. If the tube is 10 m long, what is the required heat flux? If fluid enters the tube with a fully developed velocity profile and a uniform
temperature profile, what is the surface temperature at the tube exit and at a distance of o.5 m from the entrance? Fluid properties may be
approximated as p = 1000 kg/m³, c, = 4000 J/kg · K, µ = 2 × 10-3 kg/s · m, k = 0.8 W/m · K, and Pr = 10.
To cool hot oil, an engineer has suggested that the oil be pumped through a pipe submerged in a nearby lake. The pipe (external diameter = 15 cm) will be placed in the horizontal direction. The temperature of the outer surface of the pipe averages 125 ° C. The surrounding water temperature is assumed to be constant at 15 ° C. Pipe length 100 m. If it is assumed that there is no water movement.
a. Determine the convective heat transfer coefficient of the outer pipe surface to the water. = ..... Watt / (m² ° C)
b. Determine the heat transfer rate from the pipe to the water. = ..... kW
Chapter 1 Solutions
Fundamentals of Heat and Mass Transfer
Ch. 1 - The thermal conductivity of a sheet of rigid,...Ch. 1 - The heat flux that is applied to the left face of...Ch. 1 - A concrete wall, which has a surface area of 20m2...Ch. 1 - The concrete slab of a basement is 11 in long. 8...Ch. 1 - Consider Figure 1.3. The heat flux in the...Ch. 1 - The heal flux through a wood slab 50 mm thick,...Ch. 1 - The inner and outer surface temperatures of a...Ch. 1 - A thermodynamic analysis of a proposed Brayton...Ch. 1 - A glass window of width W=1m and height H=2m is 5...Ch. 1 - A freezer compartment consists of a cubical cavity...
Ch. 1 - The heat flux that is applied to one face of a...Ch. 1 - An inexpensive food and beverage container is...Ch. 1 - What is the thickness required of a masonry wall...Ch. 1 - A wall is made from an inhomogeneous...Ch. 1 - The 5-mm-thick bottom of a 200-mm-diameter panmay...Ch. 1 - A square silicon chip (k=150W/mK) is of width...Ch. 1 - For a boiling process such as shown in Figure 1.5...Ch. 1 - You’ve experienced convection cooling if you’ve...Ch. 1 - Air at 40°C flows over a long, 25-mm-diameter...Ch. 1 - A wall has inner and outer surface temperatures of...Ch. 1 - An electric resistance heater is embedded in a...Ch. 1 - The free convection heat transfer coefficient on a...Ch. 1 - A transmission case measures W=0.30m on a sideand...Ch. 1 - A cartridge electrical heater is shaped as a...Ch. 1 - A common procedure for measuring the velocity of...Ch. 1 - A square isothermal chip is of width w=5mm on...Ch. 1 - The temperature controller for a clothes dryer...Ch. 1 - An overhead 25-m-long, uninsulated industrial...Ch. 1 - Under conditions for which the same room...Ch. 1 - A spherical interplanetary probe of 0.5-m diameter...Ch. 1 - An instrumentation package has a spherical outer...Ch. 1 - Consider the conditions of Problem 1.22. However,...Ch. 1 - If TsTsur in Equation 1.9, the radiation heat...Ch. 1 - A vacuum system, as used ¡n sputtering...Ch. 1 - An electrical resistor is connected to a battery,...Ch. 1 - Pressurized water (pin=10bar,Tin=110C) enters...Ch. 1 - Consider the tube and inlet conditions of Problem...Ch. 1 - An internally reversible refrigerator has a...Ch. 1 - A household refrigerator operates with cold-...Ch. 1 - Chips of width L=15mm on a side are mounted to...Ch. 1 - Consider the transmission case of Problem 1...Ch. 1 - One method for growing thin silicon sheets for...Ch. 1 - Heat is transferred by radiation and convection...Ch. 1 - Radioactive wastes are packed in a long,...Ch. 1 - An aluminum plate 4 mm thick is mounted in a...Ch. 1 - A blood warmer is to be used during the...Ch. 1 - Consider a carton of milk that is refrigerated at...Ch. 1 - Prob. 1.48PCh. 1 - Liquid oxygen, which has a boiling into of 90 K...Ch. 1 - The emissivity of galvanized steel sheet, a...Ch. 1 - Three electric resistance heaters of length...Ch. 1 - A hair dryer may be idealized as a circular duct...Ch. 1 - In one stage of an annealing process, 304...Ch. 1 - Convection ovens operate on the principle of...Ch. 1 - Annealing, an important step ¡n semiconductor...Ch. 1 - In the thermal processing of semiconductor...Ch. 1 - A furnace tor processing semiconductor materials...Ch. 1 - Prob. 1.58PCh. 1 - Consider the wind turbine of Example 1.3. To...Ch. 1 - Consider the conducting rod of Example 1.4...Ch. 1 - A long bus bar (cylindrical rod used for making...Ch. 1 - A 50mm45mm20mm cell phone chargerhas a surface...Ch. 1 - A spherical, stainless steel (AISI 302) canister...Ch. 1 - A freezer compartment is covered with a...Ch. 1 - A vertical slab of Wood’s metal is joined to a...Ch. 1 - A photovoltaic panel of dimension 2m4m isinstalled...Ch. 1 - Following the hot vacuum forming of a...Ch. 1 - Prob. 1.69PCh. 1 - A computer consists of an array of five printed...Ch. 1 - Prob. 1.71PCh. 1 - The roof of a car in a parking lot absorbs a solar...Ch. 1 - Consider the conditions of Problem 1.22,but the...Ch. 1 - Most of the energy we consume as food ¡s converted...Ch. 1 - Prob. 1.75PCh. 1 - The wall of an oven used to cure plastic parts is...Ch. 1 - An experiment to determine the convection...Ch. 1 - A thin electrical heating element provides a...Ch. 1 - A rectangular forced air healing duct is suspended...Ch. 1 - Consider the steam pipe of Example 1.2. The...Ch. 1 - During its manufacture, plate glass at 600°C is...Ch. 1 - The curing press of Example 1.9 involves exposure...Ch. 1 - The diameter and surface emissivity of an...Ch. 1 - Prob. 1.84PCh. 1 - A solar flux of 700W/m2K is incident on a...Ch. 1 - In considering the following problems involving...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Water at 10C temperature flowing from a pipe with a diameter of 100mm at a speed of 2m / s, air from a pressure of 2 ATM at 180F flowing at a speed of 50 ft / s from a pipe with a diameter of 2 in, and an oil with a specific gravity of 0.78 and a diameter of 20 cp at a speed of 5 ft / s through a 2in pipe. Shows the flow state of the biopolymer melt flowing through the pipeline at a speed of 0.2 m/s, with a density of 900 kg/m3 and a density of 1 Pa-sarrow_forwardQ2) Derive an equation for the temperature profile in the wall and calculate the temperature at the solid-fluid interface for the one-dimensional heat transfer problem schematically shown below. Heat is volumetrically generated within the wall. The thickness of the wall is L. A fluid flows on the left side of the wall while the right side is insulated. The convective heat transfer coefficient is h, the temperature and velocity of the fluid is To and Væ, respectively. Given that, L= 30 mm, k =7 W/m K, h = 400 W/m2.K, T = 25°C, q = 1.00xl06 W/m³. Well insulated k wall V. T, h Fluidarrow_forwardThe condenser of a steam power plant consists of AISI 302 Stainless steel tubes, each with outer and inner diameters of 35 mm and 30 mm, respectively. Saturated steam at 0.135 bar condenses on the outer surface of the tube, while water at a mean temperature of 295 K is in fully developed flow through the tube (you can assume that 295 K is the mean temperature in the axial direction of the tube (e.g. along its length) or you may assume that the inlet water temperature is 295 K). For a water mass flow rate of 0.22 kg/s, what is the outer surface temperature of the tube and the rates of heat transfer and steam condensation per unit tube length? As an approximation you may evaluate the properties of the liquid film at the saturation temperature.arrow_forward
- Merrill et al. (1965) in a series of classic experiments studied the flow of blood in capillary tubes of various diameters. The blood had a hematocrit of 39.3 and the temperature was 20°C. They measured the pressure drop as a function of the flow rate for five tube diameters ranging from 288 to 850 μm. When they expressed the measured pressure drops in terms of the wall shear stress, and the volumetric flow rates in terms of the reduced average velocity, all of the data for the various tube sizes formed, within the experimental accuracy, a single line as predicted by the Rabinowitsch equation expressed in terms of reduced average velocity. From their results they provide the following values of the Casson parameters at 20°C: τy = 0.0289 dynes cm−2 and s = 0.229 (dynes s cm−2)1/2. Using these values for τy and s, show that the equation below for reduced average velocity provides an excellent fit to their data summarized in the following table. (Wall shear stress) τw , dynes cm-2…arrow_forwardVI.2 A coolant is transported in a pipe with external wall temperature of -30 °C and with outer diameter of 10 cm. The tube is thermally isolated by two layers: 1) an internal layer of foamed polypropylene with thermal conductivity of 0.08 W.m.K and thickness of 10 cm, and 2) an external felt layer with thermal conductivity of 0.05 W.m.K and thickness of 5 cm. Temperature of the outer surface is 25 °C. Calculate the heat flow from the surroundings to the tube with length of 100 m. What is the temperature on the boundary between polypropylene and felt layers? Result: The heat flow from the surroundings is approx. 1.77 kW. Temperature between layers of isolation is 8.8 °C.arrow_forwardIt is aimed to produce frozen potatoes in a newly established business. The entry temperature of the cleaned potato to the system is -16 °C, and the desired temperature to reach 10 °C. For this purpose, a refrigerant at -25 °C will be used. In the freezing process, potatoes of certain sizes are placed in the ice cream basket, the basket is immersed in the tank containing the refrigerant and kept during freezing. A cooling system is designed around the tank and 1M Joule per hour removes heat from the tank to keep the temperature of the tank constant at -25 °C. It is desirable to produce potatoes of different shapes. These shapes are spheres with a diameter of 20 mm, a cube with dimensions of 16x16x16 mm and a rectangular prism with a diameter of 12x12x25 mm. In such a process,a. What should be used as refrigerant?b. What is the daily production capacity for each product?c. What would you recommend to increase production capacity?arrow_forward
- Water going into a pipe with a tempeture of T1 and going out T2 . ambient tempeture is T0. flow rate q. Develop an expression for T2 ( based on heat transfer) Length of the pipe Lh0 - convective heat transfer coefficient of the airhW -convective heat transfer coefficient of the waterk- pipe thermal conductivity (W/m·K)d – pipe diameter Use any other varilable that you need and can be found online easily .arrow_forward5.41 A steel pipe 1 m in diameter and 40 mm wall thickness is heavily insulated on the outside and is originally at -20°C. A hot oil at 60°C is now pumped through the pipe resulting in a convective surface condition with h = 500 W/m2 K at the inner surface of the pipe. What is the temperature of the exterior pipe surface 8 min after the start of flow. Also calculate the heat flux to the pipe from the oil and the energy transferred per metre of pipe length from the oil to the pipe at/ = 8 min. (For steel at 20°C, p = O= 18.8 x 10-6 m2/s) 434 J/kg. K, k = 63.9 W/mK, [41°C,-8000 W/m2,-2.6x 107 J/m] 7823 kg/m, c =arrow_forward5. Steam condensing on the outer surface of a thin-walled circular tube of 50 mm diameter and 6 m length maintains a uniform surface temperature of 100 C. Water flows through the tube at a rate of m= 0.25 kg/s, and its inlet and outlet temperatures are Tmi = 15 C and Tmo = 57C. What is the average convection coefficient associated with the water flow? Data: Pvater = 1000 kg/m³ ; c, = 4.2 kJ/kg-K.arrow_forward
- When can the conductive thermal resistance of the tube in a heat exchanger be neglected in overall heat transfer coefficient calculation? Never When the tube is thin or the material is highly conductive When the tube is thin. When the tube material is highly conductive. Which of the following sentence(s) is/are true? We cannot calculate thermal resistance of a solid slab. Thermal resistance concept is applicable only in Cartesian or Cylindrical coordinate. We cannot calculate thermal resistance of a solid cylinder. To apply thermal resistance concept, a problem only needs to be one dimensional and steady.arrow_forwardProblem 6. ART TAT Consider the cylindrical pipe shown in the figure. Heat is being generated in the pipe wall at a rate of R in units of W/m³, and the thermal conductivity of the wall is k, the heat transfer coefficients at the inside and outside of the pipe are h; and ho, respectively. At a given location along the pipe axis, the temperature of the fluid flowing inside of the pipe is Ti and that at the outside is To i. ii. Find the expression for the temperature distribution in the pipe wall. Find the total heat transfer rate from the pipe to both fluids.arrow_forwardA square isothermal chip is of width 5mm on a side mounted in a substrate such that its side and back surfaces are well insulated, while the front surface is exposed to the flow of coolant at 15C. From reliability considerations, the chip temperature must not exceed 85C. If air is used as a coolant, h = 200W/m2. If a dielectric liquid is used as coolant, h = 3000W/m2. What is the difference in maximum allowable power through the chip between the two coolants? (answer in W) *arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license